manualshive.com logo in svg

Thermo Scientific ISQ 7000, Руководство по оборудованию


Поделиться
Скачать
background image

 

3 

Advanced Maintenance

Replacing Components of the Analyzer

Thermo Scientific

ISQ 7000 Hardware Manual

149

Analyzer Tray

This section provides instructions for replacing the analyzer tray. The analyzer tray itself is 
unlikely to fail, but you must follow these steps anytime you remove the analyzer tray from 
the ISQ 7000 mass spectrometer to service or replace other components.

Shutting Down the ISQ 7000 System

To shut down the ISQ 7000 system

1. Remove the ion source cartridge according to 

“Ion Source Cartridge” 

on 

page 216

.

2. Cool down the GC oven.

3. If you are using hydrogen as a carrier gas, cool down the injector to prepare the GC for 

powering off. See the GC documentation for more information. After the heated zones 
are cooled down, power-off the GC.

WARNING  - INSTRUMENT DAMAGE

 Thermo Fisher Scientific strongly recommends 

that only trained Thermo Fisher Scientific Field Service Engineers remove the analyzer 
tray and service its components.

AVERTISSEMENT DOMMAGES À L’INSTRUMENT 

Thermo Fisher Scientific recommande 

fortement que seuls des ingénieurs de maintenance sur site de Thermo Fisher Scientific se 
chargent d’enlever le plateau de l’analyseur et de procéder à la maintenance de ses 
composants.

Note  

See the 

ISQ and TSQ GC-MS Spare Parts Guide

 for information about ordering this 

component.

WARNING  BURN HAZARD:  

The injector, oven, and transfer line may be hot. Allow them 

to cool to room temperature before touching them.

AVERTISSEMENT RISQUE DE BRÛLURE

:  l’injecteur, le four et la ligne de transfert 

peuvent être chauds. Laissez-les refroidir à la température ambiante avant de les toucher.

WARNING  FIRE HAZARD: 

If you are using hydrogen as a carrier gas, you must cool down 

and shut off the GC to prevent the buildup of hydrogen in the vacuum manifold. See the 

“Hydrogen Safety Precautions” 

on 

page xvi

 of the Preface for more information.

Содержание ISQ 7000



























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ISQ 7000

CAENels CT-BOX User Manual preview
CT-BOX
Бренд: CAENels Страницы: 75
Nellcor OxiMax N-550 Operator'S Manual preview
OxiMax N-550
Бренд: Nellcor Страницы: 104
Oceanic VEO 1.0 Operating Manual preview
VEO 1.0
Бренд: Oceanic Страницы: 68
Oceanic BUD Operating Manual preview
BUD
Бренд: Oceanic Страницы: 24
JUMO LOGOSCREEN 601 Manual preview
LOGOSCREEN 601
Бренд: JUMO Страницы: 24
Fronius LaserHybrid SB 360i Operating Instructions Manual preview
LaserHybrid SB 360i
Бренд: Fronius Страницы: 104
aboni HydroTracer FLV Operation Manual preview
HydroTracer FLV
Бренд: aboni Страницы: 48
Vectronics PM-30 SWR Owner'S Manual preview
PM-30 SWR
Бренд: Vectronics Страницы: 2
Resol WMZ Plus Installation & Operation Manual preview
WMZ Plus
Бренд: Resol Страницы: 24
Endress+Hauser Cerabar S PMC71 Functional Safety Manual preview
Cerabar S PMC71
Бренд: Endress+Hauser Страницы: 48
Lambda OXYMETER Calibration Procedure preview
OXYMETER
Бренд: Lambda Страницы: 2
Hamilton Sundstrand Company Fuel Metering Valves eXVG Supplementary Manual preview
Fuel Metering Valves eXVG
Бренд: Hamilton Sundstrand Company Страницы: 36
Hanna Instruments HI96101C Instruction Manual preview
HI96101C
Бренд: Hanna Instruments Страницы: 48
A&D LCB03 Series Instruction Manual preview
LCB03 Series
Бренд: A&D Страницы: 2
Bauhn PA39085 Instruction Manual preview
PA39085
Бренд: Bauhn Страницы: 16
BERTHOLD TECHNOLOGIES LB 444 Operating Manual preview
LB 444
Бренд: BERTHOLD TECHNOLOGIES Страницы: 127
Modern Water OVA 7000 Routine Service Manual preview
OVA 7000
Бренд: Modern Water Страницы: 17
Endress+Hauser Liquicap M FTI51 Operating Instructions Manual preview
Liquicap M FTI51
Бренд: Endress+Hauser Страницы: 96

Бренды по названию

Популярные бренды

Загрузить еще бренды