manualshive.com logo in svg

Thermo Scientific ISQ 7000, Руководство по оборудованию


Поделиться
Скачать
background image

1

  Performing Routine Maintenance

Cleaning Durable Components

108

ISQ 7000 Hardware Manual

Thermo Scientific

Cleaning Durable Components

You can clean the following durable components inside the vacuum manifold:

• Repeller
• Repeller plate
• Repeller nut
• Repeller spring
• Filament retaining spring
• Ion  volume
• Lens  1
• Lens  2 
• Lens  3/RF  lens
• Ion  cartridge  sleeve
• Ion source block
• Ion  guide
• Heat shield for the source interface board
• Screws 

To clean durable components of the ISQ 7000 mass spectrometer, you will need the following 
cleaning supplies:

• Acetone, reagent grade (or other suitable polar solvent)
• Aluminum oxide abrasive powder, number 600
• Applicators, cotton-tipped 
• Cotton swab with wooden handle
• Deionized  water
• Detergent (Alconox, Micro, or equivalent)
• Dremel rotary tool or equivalent (recommended)
• Forceps
• Gas, clean and dry (Nitrogen, Helium or equivalent)
• Glass beaker
• Gloves, cleanroom (see the 

ISQ Spare Parts Guide

 for ordering information.)

• Glycerol, reagent grade
• Razor blade
• Toothbrush that will not leave any plastic residue
• Ultrasonic cleaner

IMPORTANT  

If there is any doubt about compatibility of decontamination or cleaning 

agents with parts of the equipment or material contained in it, the responsible party must 
contact Thermo Fisher Scientific product support personnel.

Note  

You only need to clean the repeller, ion volume and all the lenses the most 

frequently. Cleaning the other components are not part of the expected maintenance.

WARNING  MATERIAL AND EYE HAZARD: 

Wear impermeable laboratory gloves and eye 

protection when cleaning components.

Содержание ISQ 7000



























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ISQ 7000

Baker Hughes Masoneilan 12400 Series Instruction Manual & Safety Manual preview
Masoneilan 12400 Series
Бренд: Baker Hughes Страницы: 81
Parr Instrument 6400 Operating Instructions Manual preview
6400
Бренд: Parr Instrument Страницы: 110
Bamo Pooltest 3 Instruction Manual preview
Pooltest 3
Бренд: Bamo Страницы: 8
Lumel N32H User Manual preview
N32H
Бренд: Lumel Страницы: 32
VEE GEE BX-3 Operation Manual preview
BX-3
Бренд: VEE GEE Страницы: 2
Varian CP-4900 Micro-GC Preinstallation Manual preview
CP-4900 Micro-GC
Бренд: Varian Страницы: 7
Vapotherm precision flow Quick Reference Manual preview
precision flow
Бренд: Vapotherm Страницы: 2
Endress+Hauser CNGmass DCI Operating Instructions Manual preview
CNGmass DCI
Бренд: Endress+Hauser Страницы: 88
Balluff BML-S1G0-Q71 Series Condensed Manual preview
BML-S1G0-Q71 Series
Бренд: Balluff Страницы: 20
C.R. Laurence PAL1K User Manual preview
PAL1K
Бренд: C.R. Laurence Страницы: 4
Neogen AccuPoint Quick Start Manual preview
AccuPoint
Бренд: Neogen Страницы: 9
LaserLiner 4K5 RA 800 Manual preview
4K5 RA 800
Бренд: LaserLiner Страницы: 52
Saturn South SS9007.3 Mini CT Meter User Manual preview
SS9007.3 Mini CT Meter
Бренд: Saturn South Страницы: 18
PCB Piezotronics IMI Sensors 66212ANZ2 Installation And Operating Manual preview
IMI Sensors 66212ANZ2
Бренд: PCB Piezotronics Страницы: 6
TEA 800506 Instruction Manual preview
800506
Бренд: TEA Страницы: 10
Velleman DVM401 Manual preview
DVM401
Бренд: Velleman Страницы: 18
LaserLiner MoistureMaster Compact Plus Manual preview
MoistureMaster Compact Plus
Бренд: LaserLiner Страницы: 80
SIGRIST StackGuard Instruction Manual preview
StackGuard
Бренд: SIGRIST Страницы: 54

Бренды по названию

Популярные бренды

Загрузить еще бренды