Thermo Scientific GENESYS 10S Vis Скачать руководство пользователя страница 80

Страница: 80 / 134

Absorbance Ratio

Setting Up Test Parameters

GENESYS 10S Vis User Guide

Thermo Scientific

2. Highlight the test to recall and press

Enter

This screen provides these capabilities:

•

Setting Up Test Parameters

•

Cell Correction

•

Saving a Test

• Viewing the list of stored tests

•

Measuring a Blank

Setting Up Test Parameters

To set up test parameters

1. In the Absorbance Ratio screen, highlight the desired parameter.

2. When the parameters are set, press

Save Test

to save the test or

Run Test

to measure a

blank or samples.

Measuring Samples

To measure samples automatically (using Auto 6 or Auto 3)

1. Install the blank and samples.

Note

If Cell Correction is ON, you must run the Setup Correction application before

you can access Run Test or Measure Samples.

Note

If Auto Save Data is ON, you must enter a Data File Name before you can

access Run Test or Measure Samples.

Содержание GENESYS 10S Vis







































































































































Результаты поиска

Содержание GENESYS 10S Vis

Отзывы:

Похожие инструкции для GENESYS 10S Vis

Бренды по названию

Популярные бренды

Thermo Scientific GENESYS 10S Vis, Руководство пользователя

Результаты поиска

Содержание GENESYS 10S Vis

Отзывы:

Похожие инструкции для GENESYS 10S Vis

Бренды по названию

Популярные бренды