Thermo Scientific EX-111, Инструкция по эксплуатации

Страница: 7 / 26

- 6 -
Section III Installation Section III Installation
Section III Installation Section III Installation
Section III Installation
Site Site
Site Site
Site
Never place the unit in a location where excessive heat, moisture, or Never place the unit in a location where excessive heat, moisture, or Never place the unit in a location where excessive heat, moisture, or Never place the unit in a location where excessive heat, moisture, or Never place the unit in a location where excessive heat, moisture, or
corrosive materials are present. corrosive materials are present.
corrosive materials are present. corrosive materials are present.
corrosive materials are present.
Lift the unit by grasping it under the case, near the rubber feet.
Locate the unit on a sturdy table or bench top. Ambient temperatures should
be inside the range of +50°F to +80°F (+10°C to +27°C).
Electrical Electrical
Electrical Electrical
Electrical
Requirements Requirements
Requirements Requirements
Requirements
Line voltage may be easily accessible inside the pump/control box. Line voltage may be easily accessible inside the pump/control box.
Line voltage may be easily accessible inside the pump/control box. Line voltage may be easily accessible inside the pump/control box. Line voltage may be easily accessible inside the pump/control box.
Always unplug the unit prior to removing pump/control box cover. Always unplug the unit prior to removing pump/control box cover.
Always unplug the unit prior to removing pump/control box cover. Always unplug the unit prior to removing pump/control box cover.
Always unplug the unit prior to removing pump/control box cover.
Refer to the serial number label on the rear of the unit to identify the specific
electrical requirements of your unit.
Ensure the voltage of the power source meets the specified voltage, ±10%.
The unit construction provides extra protection against the risk of electric
shock by grounding appropriate metal parts. The extra protection may not
function unless the power cord is connected to a properly grounded outlet. It
is the user's responsibility to assure a proper ground connection is provided.
For 220 - 240 volt units supplied without a line cord, use a harmonized For 220 - 240 volt units supplied without a line cord, use a harmonized
For 220 - 240 volt units supplied without a line cord, use a harmonized For 220 - 240 volt units supplied without a line cord, use a harmonized For 220 - 240 volt units supplied without a line cord, use a harmonized
(HAR) grounded 3-conductor cord, type (HAR) grounded 3-conductor cord, type
(HAR) grounded 3-conductor cord, type (HAR) grounded 3-conductor cord, type
(HAR) grounded 3-conductor cord, type H 0 5 H 0 5
H 0 5 H 0 5
H 0 5 V V V V
V V V V
V V - F - F
- F - F
- F , with conductors , with conductors
, with conductors , with conductors
, with conductors
listed below. A suitable cord end is required for connecting to the listed below. A suitable cord end is required for connecting to the
listed below. A suitable cord end is required for connecting to the listed below. A suitable cord end is required for connecting to the
listed below. A suitable cord end is required for connecting to the
equipment (see unit socket) and must terminate with an IEC approved equipment (see unit socket) and must terminate with an IEC approved
equipment (see unit socket) and must terminate with an IEC approved equipment (see unit socket) and must terminate with an IEC approved equipment (see unit socket) and must terminate with an IEC approved
plug for proper connection to power supply. plug for proper connection to power supply.
plug for proper connection to power supply. plug for proper connection to power supply.
plug for proper connection to power supply.
NON-BOOST HEATER UNITS NON-BOOST HEATER UNITS NON-BOOST HEATER UNITS NON-BOOST HEATER UNITS NON-BOOST HEATER UNITS Nominal 1.0 mm Nominal 1.0 mm Nominal 1.0 mm Nominal 1.0 mm Nominal 1.0 mm 2 2
2 2
2 cross section rated 10 Amps cross section rated 10 Amps cross section rated 10 Amps cross section rated 10 Amps cross section rated 10 Amps
Unit Socket: IEC - 320 C13 Unit Socket: IEC - 320 C13
Unit Socket: IEC - 320 C13 Unit Socket: IEC - 320 C13
Unit Socket: IEC - 320 C13
BOOST HEATER UNITS BOOST HEATER UNITS BOOST HEATER UNITS BOOST HEATER UNITS BOOST HEATER UNITS Nominal 1.5 mm Nominal 1.5 mm Nominal 1.5 mm Nominal 1.5 mm Nominal 1.5 mm
2 2 2 2 2
cross section rated 16 Amps cross section rated 16 Amps cross section rated 16 Amps cross section rated 16 Amps cross section rated 16 Amps
Unit Socket: IEC - 320 C19 Unit Socket: IEC - 320 C19 Unit Socket: IEC - 320 C19 Unit Socket: IEC - 320 C19 Unit Socket: IEC - 320 C19