Thermo Scientific EASY-Spray NG Скачать руководство пользователя страница 59

Страница: 59 / 62

Thermo Scientific

EASY-Spray Series Ion Source User Guide

Contents of the Installation Kits

lists the parts supplied in the EASY-Spray NG Ion Source Kit (P/N ES082) and the

EASY-Spray Ion Source Kit (P/N ES081), which are identical except for the source housing.
For a list of replaceable parts, see

Chapter 8, “Replaceable Parts.”

Note

As of 2018, these ion source kits exclude the LCD monitor (P/N ES217) and the

1.5 mm hex key.

Table 8.

Contents of the EASY-Spray Series ion source kits (Sheet 1 of 2)

Image

Description

Quantity

Part number

Provided in the EASY-Spray NG Ion Source Kit (P/N ES082)

See

Figure 2

EASY-Spray NG housing

–

Provided in the EASY-Spray Ion Source Kit (P/N ES081)

See

Figure 3

. EASY-Spray

housing

–

Provided in both ion source kits

Controller power supply assembly:

• Power supply, 24 Vdc output (shown

without the input plug)

• Power adapter cable

ES231

Dino-Lite analog camera and power
supply

–or–
Dino-Lite USB camera and software disc;
USB extension cord

ES216

–or–

ES218 (camera);
00302-99-00095
(cord)

EASY-Spray column, 15 cm × 75 μm ID,
PepMap C18, 3 μm particle size

ES800

Содержание EASY-Spray NG































































Результаты поиска

Содержание EASY-Spray NG

Отзывы:

Похожие инструкции для EASY-Spray NG

Бренды по названию

Популярные бренды

Thermo Scientific EASY-Spray NG, Руководство пользователя

Результаты поиска

Содержание EASY-Spray NG

Отзывы:

Похожие инструкции для EASY-Spray NG

Бренды по названию

Популярные бренды