Thermo Scientific EASY-Spray NG Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 62

background image

5

Configuring the Mass Spectrometer for NSI Mode

Configuring the EASY-Spray Source’s NSI Parameters

32

EASY-Spray Series Ion Source User Guide

Thermo Scientific

Figure 20.

Ion Source pane in the Tune window (example)

4. Click

Apply

.

Configuring the EASY-Spray Source’s NSI Parameters

After you complete the instrument configuration, use the Thermo Tune Plus application to
configure the NSI source parameters. For additional information, refer to the Tune Plus Help.



To set the NSI source parameters

1. Open the Tune Plus application by choosing

Start > All Apps

(Windows 10) or

All

Programs

(Windows 7)

> Thermo Instruments

(or

Thermo

Model

) and so on.

2. Choose

Setup > NSI Source

, and then enter

1.90

in the Spray Voltage (kV) box

).

Use 1.90 kV as the start value for the spray voltage. If the intensity of the full-scan
spectrum is low, gradually increase the spray voltage to improve the spectrum. The
recommended range for the spray voltage is 1.40–2.40 kV.

Figure 21.

NSI Source dialog box

3. Click

OK

.

Enter the
absolute value.

«
...
44
45
46
47
48
...
»

Содержание EASY-Spray NG































































Отзывы:

Нет отзывов

Похожие инструкции для EASY-Spray NG

Бренд: Parker Research Corp Страницы: 3

Бренд: S.I.T.A. Страницы: 32

Бренд: MAHLE Страницы: 21

Бренд: Vahterus Страницы: 31

Бренд: Waters Страницы: 250

Бренд: Waters Страницы: 141

Бренд: Zero 88 Страницы: 12

Бренд: Zest4Leisure Страницы: 4

Бренд: Zeiss Страницы: 119

Бренд: Zehnder Rittling Страницы: 32

LUNAQUA Classic LED

Бренд: Oase Страницы: 16

Бренд: Channel Master Страницы: 7

Бренд: Rottler Страницы: 96

Бренд: WIFO Страницы: 24

Бренд: Buyers Страницы: 2

Бренд: Drive Страницы: 2

Бренд: TECALEMIT Страницы: 19

Бренд: Boxym Страницы: 49

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды