Thermo Scientific EASY-Spray NG Скачать руководство пользователя страница 40

Страница: 40 / 62

Connecting the EASY-Spray Column Plumbing

Examples of LC Connections to the EASY-Spray Column

EASY-Spray Series Ion Source User Guide

Thermo Scientific



To plumb a two-column setup for the EASY-nLC 1200 instrument

1. Assemble and connect the Column Out line as follows:

a. Insert the Column Out line’s nanoViper fitting into the Viper union, and then

connect the other end of the union to the appropriate end of the nanoViper
precolumn.

b. Alternate tightening each fitting in increments until you feel resistance, and then

tighten both fittings by an additional 1/8-turn (45 degrees). Do not tighten the
fittings by more than 1/4-turn.

On the other end of the precolumn, insert the fitting into the venting Tee’s side port
(

Figure 13

), and then tighten 1/8- to 1/4-turn (45–90 degrees).

2. On the Waste In line, insert the fitting into the venting Tee’s bottom port, tighten the

fitting by hand until you feel resistance, and then tighten the fitting again by an
additional 1/8- to 1/4-turn. Do not tighten the fitting by more than a 1/4-turn.

3. Insert a 3 mm hex key into the bolt that secures the (venting) Tee holder to the column

holder, loosen the hex bolt, and then slowly move the Tee holder forward.

4. Connect the venting Tee to the EASY-Spray column (

Figure 16

Figure 16.

Example of a two-column setup with nanoViper fittings and a Viper union

5. Adjust the Tee holder’s position so that it supports the nanoViper fitting, and then use a

3 mm hex key to tighten the hex bolt on the bottom of the column holder.

Note

Follow the recommended flow direction stated on the precolumn label.

Note

See the Caution on

page 24

regarding the nanoViper fittings.

Column Out line

Waste In line

EASY-Spray column

Содержание EASY-Spray NG































































Результаты поиска

Содержание EASY-Spray NG

Отзывы:

Похожие инструкции для EASY-Spray NG

Бренды по названию

Популярные бренды

Thermo Scientific EASY-Spray NG, Руководство пользователя

Результаты поиска

Содержание EASY-Spray NG

Отзывы:

Похожие инструкции для EASY-Spray NG

Бренды по названию

Популярные бренды