Thermo Scientific EASY-Spray NG Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 62

background image

© 2018 Thermo Fisher Scientific Inc. All rights reserved.

Accucore, EASY-nLC, EASY-Spray NG, Exactive, LCQ Fleet, nanoViper, PepMap, PepSwift, TSQ, and Viper
are trademarks; Unity is a registered service mark; and Acclaim, Dionex, EASY-Spray, LCQ, LTQ, Optima,
Orbitrap, Orbitrap Fusion, Thermo Scientific, Tribrid, UltiMate, and Xcalibur are registered trademarks of
Thermo Fisher Scientific Inc. in the United States. Fisher Scientific is a registered trademark of Fisher Scientific
Co. in the United States.

The following are registered trademarks in the United States and other countries: Microsoft and Windows are
registered trademarks of Microsoft Corporation.

The following are registered trademarks in the United States: Dino-Lite and DinoCapture are registered
trademarks of AnMo Electronics Corporation. IDEX is a registered trademark of IDEX Corporation.
Nanospray is a registered trademark of AB Sciex Pte. Ltd.

All other trademarks are the property of Thermo Fisher Scientific Inc. and its subsidiaries.

Thermo Fisher Scientific Inc. provides this document to its customers with a product purchase to use in the
product operation. This document is copyright protected and any reproduction of the whole or any part of this
document is strictly prohibited, except with the written authorization of Thermo Fisher Scientific Inc.

The contents of this document are subject to change without notice. All technical information in this
document is for reference purposes only. System configurations and specifications in this document supersede
all previous information received by the purchaser.

This document is not part of any sales contract between Thermo Fisher Scientific Inc. and a purchaser. This
document shall in no way govern or modify any Terms and Conditions of Sale, which Terms and Conditions of
Sale shall govern all conflicting information between the two documents.

Release history: Rev A, April 2017; Rev B, June 2018

For Research Use Only. Not for use in diagnostic procedures.

«
1
2
3
4
...
»

Содержание EASY-Spray NG































































Отзывы:

Нет отзывов

Похожие инструкции для EASY-Spray NG

Бренд: OMCA Страницы: 72

Бренд: Barko Hydraulics Страницы: 92

Бренд: Cannon Страницы: 40

Бренд: NARGESA Страницы: 34

Бренд: Hantek Страницы: 124

Бренд: Hameg Страницы: 10

Бренд: Xtricity Страницы: 4

Бренд: Harris Страницы: 21

Бренд: DC Med Страницы: 2

Бренд: ultraMEDIC Страницы: 28

Бренд: Evermed Страницы: 16

Бренд: Enerpac Страницы: 36

NOVACAT X8 COLL

Бренд: Pottinger Страницы: 91

WEIDER SHAPE GLIDER WECR43062

Бренд: ICON Health & Fitness Страницы: 6

Бренд: Duracell Страницы: 2

Бренд: XPOtool Страницы: 10

Бренд: Becker-Elektronik Страницы: 24

Бренд: Landoll Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды