Thermo Scientific BF51634BC-1 Скачать руководство пользователя страница 29

Страница: 29 / 78

Installation

Power Wiring

Thermo Scientific

4-3

Figure 3. Power Connections

5. Connect the Ground wire from the main lug on the ground bar at the left of

Terminal Block 1TB to a ground in the facility. Make sure the ground wire

connects to a bare metal surface. Always conform to wiring codes.

6. Install the rear access panel with the screws removed in Step 1.

Wire

1TB

1TB is located include the back of the furnace and on the right

side. (Refer to

Figure “Power Connection”).

Make sure that the furnace is 100% grounded. Do not ground

the furnace to a painted surface. The ground Connection must

be to a clean, bare metal surface to assure proper furnace

operation.

Содержание BF51634BC-1















































































Результаты поиска

Содержание BF51634BC-1

Отзывы:

Похожие инструкции для BF51634BC-1

Бренды по названию

Популярные бренды

Thermo Scientific BF51634BC-1, Инструкция по установке и эксплуатации

Результаты поиска

Содержание BF51634BC-1

Отзывы:

Похожие инструкции для BF51634BC-1

Бренды по названию

Популярные бренды