Thermo Scientific AI 3000 Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 108

background image

3

Installation

Who Performs the Installation

22

AI 3000/AS 3000 Sampling System - Operating Manual

Thermo Scientific

Who Performs the Installation

The AI 3000/AS 3000 II is installed by authorized Thermo Fisher Scientific field service
engineers (FSE), who will check its correct operation. For more details, please contact
Thermo Fisher Scientific local representatives. Should the instrument not be installed by
Thermo Fisher Scientific personnel, please strictly adhere to the following instructions.

Electrical Requirements

The instrument must be electrically supplied as indicated in the

“Technical Specifications”

.

How to Lift and Carry the Sampling Unit

The AI 3000/AS 3000 II must be lifted and carried by hand. See

.

Figure 20.

How to lift and carry the Sampling Unit

CAUTION

The power line and the connections between the instruments must maintain

good electrical grounding. Poor grounding represents a danger for the operator and may
seriously affect the instrument performance.

Do not connect the AI 3000/AS 3000 II to lines feeding devices of a heavy duty nature,
such as motors, UV lamps, refrigerators and other devices that can generate disturbances.

Pay attention not to leave any cable connecting the sampling unit and the
chromatographic system or the power cord close to the GC hot air vents.

«
...
38
39
40
41
42
...
»

Содержание AI 3000













































































































Отзывы:

Нет отзывов

Похожие инструкции для AI 3000

Бренд: DARKSTAR TECHNOLOGIES Страницы: 4

Бренд: TDW Страницы: 2

Бренд: Taurus Страницы: 25

Бренд: Vancare Страницы: 3

Бренд: Paitec Страницы: 14

Бренд: FENDT Страницы: 31

Бренд: Farmi Forest Corporation Страницы: 32

Martin ERA 800 Performance

Бренд: Harman Страницы: 32

Martin ERA 600 Performance

Бренд: Harman Страницы: 32

Бренд: Sabre Страницы: 2

Бренд: Tanco Страницы: 112

Бренд: Qiagen Страницы: 48

Бренд: Qiagen Страницы: 162

Бренд: Qazqa Страницы: 4

Бренд: Qlightec Страницы: 12

Бренд: Teac Страницы: 9

Бренд: Tascam Страницы: 3

Бренд: Tascam Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды