Thermo Scientific Agilent 1200 Series Скачать руководство пользователя страница 9

Страница: 9 / 58

Preface

Thermo Scientific

Agilent 1200 Series Getting Connected Guide for LC Devices

Supported Firmware Versions

LC Devices supports the model numbers and firmware versions of the Agilent 1200 Series
modules listed in

Table 1

. For instructions on how to check the firmware version, see

Chapter 1, “Checking the Agilent Firmware Versions.”

Table 1.

Supported firmware versions for the Agilent 1200 Series LC system

Module

Model number

Firmware version

High Performance Autosampler
(and Thermostat)

G1367B
(G1330B)

A.06.12

High Performance Autosampler SL
(and Thermostat)

G1367C
(G1330B)

A.06.12

Micro Well-plate Autosampler

G1377A

A.06.03

Thermostatted Column Compartment

G1316A

A.06.10

Thermostatted Column Compartment SL

G1316B

A.06.10

Binary Pump

G1312A

A.06.10

Binary Pump SL

G1312B

A.06.10

Capillary Pump

G1376A

A.06.34

Quaternary Pump

G1311A

A.06.10

Diode Array Detector (DAD)

G1315B

A.06.10

Diode Array Detector (DAD)

G1315C

B.01.03

Diode Array Detector (DAD)

G1315D

B.01.04

Variable Wavelength Detector (VWD) SL

G1314C

A.06.50

Содержание Agilent 1200 Series



























































Результаты поиска

Содержание Agilent 1200 Series

Отзывы:

Похожие инструкции для Agilent 1200 Series

Бренды по названию

Популярные бренды

Thermo Scientific Agilent 1200 Series, Руководство по подключению

Результаты поиска

Содержание Agilent 1200 Series

Отзывы:

Похожие инструкции для Agilent 1200 Series

Бренды по названию

Популярные бренды