manualshive.com logo in svg

Thermo Scientific Agilent 1200 Series, Руководство по подключению


Поделиться
Скачать
background image

2

  Setting Up the LAN Interface

Determining the LAN Interface Type and Location

6

Agilent 1200 Series Getting Connected Guide for LC Devices

Thermo Scientific

To determine which module contains the LAN interface

Check the back panels of the modules for either an on-board LAN interface (

Figure 4

) or 

a LAN card (

Figure 5

). 

Figure 4. 

Location of the on-board LAN interface port (example)

Figure 5. 

Location of the LAN card (pump module, example)

Note  

If the LC stack does not have a built-in LAN interface, Agilent recommends 

that you install the Agilent G1369 LAN card in the detector, if part of the system. If 
an Agilent detector is not part of the system, install the LAN card in the pump or 
autosampler module. For instructions, refer to the manuals that came with the 
Agilent 1200 Series LC system. 

LAN

USB

REMOTE

RS-232

CAN

CAN

CONFIG

REMOTE FLASH

PCMCIA

ANALOG

 1

ANALOG

2

Configuration switches
for an on-board LAN interface

On-board LAN interface port 

REMOTE

RS-232

CONFIG

ANALOG

CAN

CAN

Agilent Technologies

Activity

Speed

G1369 LAN Interface

Agilent G1369 LAN card

Содержание Agilent 1200 Series



























































Отзывы:

Нет отзывов

Похожие инструкции для Agilent 1200 Series

ABB ACS880-01 Series Installation Manual preview
ACS880-01 Series
Бренд: ABB Страницы: 238
B&K DT1 Owner'S Manual preview
DT1
Бренд: B&K Страницы: 8
FagronLab FG User Manual preview
FG
Бренд: FagronLab Страницы: 16
Napoleon S1 Assembly Replacement Instructions preview
S1
Бренд: Napoleon Страницы: 2
Raytheon V800 Instruction Manual preview
V800
Бренд: Raytheon Страницы: 62
Pablo CONTOUR Assembly/Installation Instructions preview
CONTOUR
Бренд: Pablo Страницы: 7
Raymarine ST70 Instrument Quick Reference Manual preview
ST70 Instrument
Бренд: Raymarine Страницы: 12
Raven SmarTrax Operation Manual preview
SmarTrax
Бренд: Raven Страницы: 73
Tascam DA-40 Tehnical Documentation preview
DA-40
Бренд: Tascam Страницы: 3
RAB Lighting SR2 Installation Instructions preview
SR2
Бренд: RAB Lighting Страницы: 4
campgo Raiju User Manual preview
Raiju
Бренд: campgo Страницы: 33
ValueStore US V16 Quick Manual preview
V16
Бренд: ValueStore US Страницы: 2
ZOLL IVTM Physician'S Manual preview
IVTM
Бренд: ZOLL Страницы: 37
Wagan 2296 User Manual preview
2296
Бренд: Wagan Страницы: 4
Wachs TFS Manual preview
TFS
Бренд: Wachs Страницы: 22
Yamaha TG500 Supplementary Manual preview
TG500
Бренд: Yamaha Страницы: 16
Yamaha TG77 Owner'S Manual preview
TG77
Бренд: Yamaha Страницы: 139
Yamaha TG77 Midi Data Format preview
TG77
Бренд: Yamaha Страницы: 19

Бренды по названию

Популярные бренды

Загрузить еще бренды