Thermo Scientific 8120 Скачать руководство пользователя страница 34

Страница: 34 / 42

1. Partially thread seat disc and nipple assembly (Item 12) (seat disc first),

into large end of bushing (Item 9), leaving tang of nipple assembly
exposed about 1/3" beyond top of bushing (nipple must rotate freely
in bushing).

2. Insert seat disc and nipple assembly (Item 12) (seat disc first), with

attached bushing, into valve body until properly seated.

3. Place stem gasket (Item 15) carefully over stem (Item 6) convex side

facing downward.

4. Insert slotted end of stem into valve body, making sure that slot fully

engages tang of seat disc and nipple assembly.

5. Place bonnet (Item 5) over stem and, while holding square end of stem

to keep it from turning, thread bonnet into valve body. Hold body
with one wrench and, using another wrench (15/16 socket), tighten
bonnet to 1000 in/lbs. torque.

Caution

Hex section of bonnet (Item 5) must be free of burrs or raised

edges and top of bonnet must be absolutely flat to provide an effective seal
with bonnet gasket washer (Item 7).



6. Install bonnet washer (Item 7) over stem (Item 6) on bonnet.

7. Place handwheel (Item 1) over stem and on bonnet.

8. Install seal (Item 10) over stem into recess of handwheel.

9. Install seal washer (Item 13) over seal at the bottom of handwheel

recess as shown.

10. With the flat side facing downward, place retainer washer (Item 8) on

top of seal.

11. Align the holes of these parts and place spring (Item 4) over seal.

12. Place spring retainer over assembly as shown, keeping center hole

aligned with parts installed in steps 6-11.

13. lnstall washer and screw (Items 3 & 14) over retainer. Tighten firmly

with a screwdriver, turning clockwise.

14. Turn handwheel (Item 1) fully clockwise to close valve.

15. Pressurize system, check valve for proper operation and check all seal

points for leaks by inspecting thoroughly.

180 liter LN2 Supply Tank 6-7

Thermo Scientific

Section 6

Service and Maintenance

Reassembly

Содержание 8120











































Результаты поиска

Содержание 8120

Отзывы:

Бренды по названию

Популярные бренды

Thermo Scientific 8120, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание 8120

Отзывы:

Бренды по названию

Популярные бренды