Thermo Scientific 074114 страница 31 Скачать руководство пользователя | Manualshive

Страница: 31 / 148

background image

2 • Description

Doc. 065378-01 1/12

23

RELAY/TTL

Connectors

TTL inputs control the following detector functions: autozero (TTL1), UV lamp
on/off (TTL3), and visible lamp on/off (TTL4). The TTL2 input is reserved.

The two TTL outputs and two relay outputs can be programmed as part of a
Chromeleon 7 instrument method or Chromeleon 6.8 program (see

or controlled manually in the software. The relay outputs can be programmed to
switch any low-voltage control. The switched current must be less than 200 mA
and 42 V peak.

The Dionex PDA Ship Kit (P/N 060977) includes a 12-pin connector
(P/N 923686) for relay and TTL connections. For installation instructions, see

USB Connector

The USB connector allows communication between the Dionex PDA and the PC
on which Chromeleon is installed. The Dionex PDA Ship Kit (P/N 060977)
includes one USB cable (P/N 063246). For installation instructions, see

.

Power Entry

The Dionex PDA power entry is socketed for a modular power cord (IEC 320
C13). The detector operates from input voltages over a range of 85 to 265 VAC,
47 to 63 Hz power, and requires a grounded, single-phase power source. The
typical input power is 100 W and the maximum line draw is 3.5 amps at 110 VAC
(when the detector power is turned on). The appropriate line voltage and
frequency are selected automatically.

NOTE Always leave the main power switch on unless instructed

to turn it off (for example, before performing a service
procedure). Use the power button on the front of the
detector for routine on/off control.

SHOCK HAZARD—To avoid electrical shock, use a grounded
receptacle. Do not operate the Dionex PDA or connect it to AC power
without an earthed ground connection.

The power supply cord is used as the main disconnect device. Make
sure the socket-outlet is located near the Dionex PDA and is easily
accessible.

«
...
29
30
31
32
33
...
»

Содержание 074114





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для 074114

Бренд: D-Link Страницы: 2

Бренд: D-Link Страницы: 44

Бренд: Panasonic Страницы: 44

Бренд: Panasonic Страницы: 32

HomeHawk KX-HNC800

Бренд: Panasonic Страницы: 2

BL-C10A - Network Camera - Pan

Бренд: Panasonic Страницы: 4

Бренд: Abode Страницы: 5

Бренд: Caddx-Caddi Controls Страницы: 6

SET-2000 Oil/Sludge

Бренд: Labkotec Страницы: 14

Бренд: Paradox Страницы: 2

Бренд: Paradox Страницы: 9

Бренд: Paradox Страницы: 35

Бренд: QSee Страницы: 9

Бренд: ESP Страницы: 12

Бренд: Rae Страницы: 2

Бренд: Abus Страницы: 2

Бренд: C.P. Electronics Страницы: 8

Бренд: Vision Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды