Thermo Scientific 074114 страница 128 Скачать руководство пользователя

Страница: 128 / 148

Dionex PDA Operator’s Manual

120

Doc. 065378-01 1/12

B.7.4

Connecting the USB Cable

Select one of the following methods to connect the Dionex PDA to the
Chromeleon computer:

•

Connect the detector directly to a USB port on the PC.

•

Connect the detector to the internal USB hub of another module in the
system, and connect the other module directly to the PC.

•

Connect the detector to an external USB hub (P/N 060392).

To connect the Dionex PDA directly to the PC:

1. Plug the “A” connector of the USB cable (P/N 063246) into the USB

port on the computer (see

Figure B-5

2. Plug the “B” connector of the USB cable into a USB receptacle on the

Dionex PDA rear panel.

Figure B-5. Dionex PDA Connected Directly to the Chromeleon PC

USB Cable

(P/N 063246)

Plug the

“B”

into the USB

receptacle on the PDA.

USB cable’s

connector

Plug the

“A”

into

USB

port on the PC.

USB cable’s

connector

the

PDA

Содержание 074114





















































































































































Результаты поиска

Содержание 074114

Отзывы:

Похожие инструкции для 074114

Бренды по названию

Популярные бренды

Thermo Scientific 074114, Руководство оператора

Результаты поиска

Содержание 074114

Отзывы:

Похожие инструкции для 074114

Бренды по названию

Популярные бренды