THERMO 2000 VOLTMAX 23, Инструкция по использованию и уходу

Страница: 2 / 38

TURBOMAX Use and Care Manual with Installation Instructions July 2014 Page
2
TURBOMAX
®
Specifications
The Turbomax indirect water has an internal copper domestic
heat exchanger made of multiple helical copper tubes
operating in parallel with a 150 psi.(200psi on ASME models
109A) maximum operating pressure rating.
All copper
components and assembly meet the low lead
requirements for potable plumbing products and adhere
to the NSF 61 standard (International Standard Drinking
Water Systems Components Health Effects
. The hot
water heater has a patented steel injector through which the
boiler water fluid enters the top side of the tank and a steel
collector through which the boiler water fluid exits at the bottom
of the tank. The tank is be made of high grade carbon steel.
All the steel joints are welded by the MIG/Argon gas process. It
has a maximum operating pressure of 150psi (200psi on
ASME model 109A). The tank is wrapped with a fiberglass
insulation jacket limiting the tank heat loss to less than ½°F per
hour. The outer steel jacket is painted with baked epoxy. The
water heater has a temperature controller (aquastat) that
makes contact when the temperature falls below the tank water
temperature set point minus an adjustable differential (10 to
40F)and breaks contact when the temperature rises over the
set point (95 to 195F). The tank has a ¾” drain ball valve
made of brass, which have a maximum working pressure of
200 psi. 3 adjustable feet support the water heater for leveling.
The hot water heater is shipped from the factory with an ASME
rated pressure relief valve set at 30psi (50 psi. on model 109 ,
65A&109A), a temperature & pressure gage (except #23, 33)
and an automatic air vent. The water heater is backed by a 15-
year warranty on residential applications and 10 years on
commercial applications (consult the terms of the warranty
included at the end of this manual).
SPECIFICATION
Model Tank
Volume Heat transfer
area (sq. ft.) Max.
DHW
flow * Utility
connection Boiler
connection Height
Dia-
meter Shipping
weight
TURBOMAX
®
109 119usgal
.
58.9 ft² 27usgpm 2’’ Sweat M 2’’ NPT M 74’’ 29’’ 555 lbs
T
URBOMAX109A 110usgal 58.9 pi² 27usgpm 2-1/2’ Sweat M 2’’-NPT M 74’’ 29’’ 755 lbs
TURBOMAX
®
65
72 usgal. 32.7 ft² 15usgpm 1-1/2’ Sweat M 1-1/2’’ NPT M 67’’ 24’’ 250 lbs
TURBOMAX 65A 67usgal 32.7 pi² 15usgpm 2’ Sweat M 1-1/2’’ NPT M 67’’ 24’’ 425 lbs
TURBOMAX
®
45 48 usgal. 32.7 ft² 15usgpm 1-1/2’’ Sweat M 1-1/4’’ NPT M 55’’ 22’’ 235 lbs
TURBOMAX
®
44
48 usgal. 26.2 ft² 12usgpm 1-1/2’’ Sweat M 1-1/4’’ NPT M 55’’ 22’’ 210 lbs
TURBOMAX
®
34 36 usgal. 26.2 ft² 12usgpm 1-1/2’’ Sweat M 1-1/4’’ NPT M 65“ 18“ 195 lbs
TURBOMAX
®
33
36 usgal. 19.6 ft² 9usgpm 1-1/4’’ Sweat M 1-1/4’’ NPT M 65“ 18“ 170 lbs
TURBOMAX
®
24
26 usgal. 26.2 ft² 12usgpm 1-1/2’’ Sweat M 1-1/4’’ NPT M 49’’ 18’’ 175 lbs
TURBOMAX 23 26usgal 19.6 f t2 9usgpm 1-1/4” Sweat M 1-1/4” NPT M 49’’ 18’’ 150 lbs
*Occasional operation at higher gpm is acceptable but must be reduced on application where constant hi flow is required .