THERMEx Wasteminator III, Руководство пользователя

Страница: 9 / 16

5.Attach Upper Mounting Assembly to Sink
B Series rubber mounting assembly（Picture 5.1）
1-1. Put one of two rubber gasket under sink flange. Ensure sink hole area is clear of
debris and place sink flange/gasket into sink hole.
1-2. Working from under the sink, slip second rubber gasket, fiber lining over the
sink flange, and then mount the feeding mouth locking screw and lock up.
1-3. Tighten three mounting screws up to sink until mounting assembly is seated
tightly and evenly against sink.
D series stainless steel mounting assembly（Picture 5.2）
2-1 Put one of two rubber gasket under sink flange. Ensure sink hole area is clear of
debris and place sink flange/gasket into sink hole.
2-2. Working from under the sink, slip second rubber gasket, fiber lining and metal
backup ring over the sink flange.
2-3. With the rubber gasket, fiber lining, backup ring and mounting ring tight
against sink bottom, slide snap ring onto sink flange until it pops into groove flange.
2-4. Tighten three mounting screws up to sink until mounting assembly is seated
tightly and evenly against sink.
2-5. Hook the tension spring one side to one of three screw, and hook another side
to the thruster slot.
C series mounting assembly（Picture 5.3）
3-1. Put one of two rubber gasket under sink flange. Ensure sink hole area is clear of
debris and place sink flange/gasket into sink hole.
3-2. Connect the cutted hose with sink flange by screwing in counterclosewisely and
tighten it up.
1
（Picture5.1） （Picture5.3） （Picture5.2）
（Picture 7.1）
6.Clean Sink Waste Pipe
Note: Failure to clean waste pipe may result in waste pipe blockage.
1. Remove trap
2. With drain auger, clear away all hardened waste material in horizontal
drain line running from drain trap to main pipe.
7.Dishwasher Attachment And Overflow Connection
Wastewater from a dishwasher can be plumbed into the disposer through the inlet
access on the upper part of the disposer. There is a plug on the inside of the inlet tube
on all models. Once removed, the knockout plug can not be replaced.
Note: If the dishwasher connection is made without removing the
plug, the dishwasher may overflow.
Remove Knockout Plug （Picture 7.1）
1. Lay disposer on its side and insert screwdriver （1） into
the dishwasher inlet so tip rests on outer edge of knockout plug.
2. Tap end of screwdriver handle with hammer until molded
plug breaks loose.
3. Remove loose knockout plug from inside disposer.
If you have a sink overflow, it should be connected to the overflow
inlet on the tailpipe. To connect the overflow, remove the plug in
the tailpipe by unscrewing the overflow connector cap.
8. Connect Disposer to Mounting Assembly
Note:
To avoid personal injury, do not position your head or body under disposer, the
unit could fall during installation.
Clear any objects from inside the disposer grind chamber before mounting the
disposer to the sink.
1.This product must be installed so that the motor reset button located on the
bottom of the disposer is readily accessible. Keep this space clear of all objects.
2.1 Life the disposer, inset the top end into the mounting assembly and turn. So the
mounting assembly bottom end end can slide into the splash guard slot. （B series
rubber clamp ring）
2.2 Position disposer with three mounting tabs aligned in position to slide over
mounting tracks. （B/D stainless steel clamp ring）
3.1 Mount the locking ring, and lock it up.（B series rubber clamp ring）
3.2 Lift disposer, insert top end ( mounting gasket) into mounting assembly, and
turn lower mounting ring to right ( with wrenchette or adjustable pliers) until
mounting tabs lock over ridges on mounting ring tracks. Make sure all three mounting
tabs are locked over ridges. Disposer will now by itself. Fix its position with tension
spring.（B/D stainless steel clamp ring）
4. Run water into sink, then check for leaks. Insert sound baffle into sink flange.
9.Attach Discharge Tube to Waste Drain Pipe
Note：
Please use the supplied spring type hose clamp. Failure to use the supplied tubes
and spring type hose clamp will void the guarantee and possibly cause premature
failure of the anti-vibration tailpipe mount.
Do not use plumber;s putty on any other disposer connection other than on sink
flange. Do not use thread sealants or pipe dope. These may harm disposer and cause
property damage.
Regularly inspect disposer and plumbing fittings for water leaks, as water leaks can
cause property damage. Manufacturer can not be held responsible for property
damage as a result of water leaks.
Discharge pipe installation （Picture 9.1）
06 05
Food Waste Disposer Users’ Manual Food Waste Disposer Users’ Manual