Thermal Solutions Boiler Control TSBC Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 48

background image

TSBC Instruction Manual

Page 40 of 48

Trouble Shooting

Diagnostic Menu (Continued)

System Menu

Display

Description

Software Revision

Displays current Software Revision.

PCB Board Temperature

The operating range for the control is 32 to 140 F.

Clear Boiler Inlet Temperature (BIT) Memory

No Action

History remains unchanged.

Yes

Clears low BIT memory.

Clear Alarm History Memory

No Action

History Remains unchanged.

Yes

Clears alarms memory.

Clear Boiler Run Time Hour Accumulator Memory

Boiler Run Time Hours are displayed in Display Mode as “Hours”.
No Action

Hours Remain unchanged.

Yes

Clears accumulated hours memory.

Clear Boiler Start/Stop Cycle Accumulator Memory

Boiler Start/Stop cycles are displayed in Display Mode as “Cycles”.
No Action

Hours Remain unchanged.

Yes

Clears accumulated cycles memory.

Clear User Installed Parameter Memory

No Action

Currently set parameter values are unchanged.

Set

Sets all parameters back to their Factory Default values.

Temperature Input Fine Calibration

All inputs are factory calibrated. However, it may become necessary to field

calibrate due to measuring errors resulting from long wire lengths or third party
sensor use. This is a single point calibration tool. To gain the greatest
benefit, it is recommended to calibrate as close as possible to the expected
operating temperature and measure the temperature at the sensor location.

Remote System Temperature (RST)
Outside Air Temperature (OAT)
Boiler Outlet Temperature (BOT)
Boiler Inlet Temperature (BIT)

Calibration Procedure:

1.  Select sensor that requires field calibration.
2.  Run boiler to rated condition.
3.  Enter the Actual RST, OAT, BOT and BIT.
4.  Display will flash back to the default (Note: Calibration number does

not remain on screen).

5. Calibration is complete. A one point calibration offset is calculated and

applied.

Param Code

Parameter Code

This number represents “Network Relevant” parameters. It can be used to

ensure that these parameters are identical when establishing a Peer-To-Peer
network.

Software Rev.

S 3.24

PCB Temperature

70 F

Actual RST

32 F

Actual OAT

-40 F

Actual BOT

32 F

Actual BIT

32 F

Clr BIT Hist

No Action

Clr Cycle Cnt

No Action

Factory Defaults

No Action

Clr Alarm Hist

No Action

Clr Run Time Cnt

No Action

«
...
38
39
40
41
42
...
»

Содержание Boiler Control TSBC

















































Отзывы:

Нет отзывов

Похожие инструкции для Boiler Control TSBC

coviva Smartbox TKP100A

Бренд: hager Страницы: 4

Бренд: Vag Страницы: 12

Бренд: Jandy Страницы: 28

Бренд: Jands Страницы: 6

MachXO5-NX Development Kit

Бренд: Lattice Semiconductor Страницы: 2

Бренд: nekos Страницы: 8

Бренд: nekos Страницы: 8

Бренд: Neles Страницы: 12

Бренд: Rain Bird Страницы: 4

Бренд: Rain Bird Страницы: 2

Бренд: Rain Bird Страницы: 140

WeatherSmart RSC600i

Бренд: Raindrip Страницы: 36

Бренд: WAGO Страницы: 16

Бренд: HQ Power Страницы: 23

Бренд: D+H Страницы: 2

Бренд: GSD Страницы: 5

DIGITAL EPIC-2 DTM

Бренд: Westlock Страницы: 33

Бренд: Samwon Tech Страницы: 104

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды