background image

EX-TRAFIRE

®

30H

Operator Manual, Revision T-15

12-48

SECTION 12: WARRANTY

WARRANTY:

SECTION 12�

Warranty terms and conditions vary to suit diverse markets and country directives�

WARRANTY

This Warranty Certificate forms an integral part of General Business Conditions (“GBC”) of 

THERMACUT, k.s. (the “Seller”) and shall apply to supplies of Goods under Contract concluded 

between the Seller and the other contracting party as the recipient of the Goods (the “Buyer”); terms 

used herein have the same meaning as is ascribed to them in the GBC

1� The Seller hereby provides to the Buyer a quality warranty (hereinafter referred to as 
the“Warranty”) affirming that the below specified goods delivered under the Contract will, for the 
below specified warranty period, retain the characteristics stipulated in technical data sheet of 
the Goods available on Seller’s webpages (www�thermacut�cz, www�ex-trafire�com) at the time of 
sending of Binding Offer (par� 2�2 of the GBC), otherwise in the quality and design suitable for the 
purpose arising out of the Contract, otherwise for usual purpose�

2� The warranty period is valid from the date the goods are delivered to the buyer (par� 5�1, 5�2  
of the GBC)�

3� Par� 3�4 and the following of the GBC shall apply to reporting (claiming) of Warranty defect, 
asserting rights from defective performance and other rights and obligation of the Seller and Buyer�

4� The warranty period is:

o Three (3) years for EX-TRAFIRE® brand power supplies 
o One (1) year for torches and lead sets

5� The Warranty does not cover reasonable wear and tear of the Goods or associated parts, which 
include consumables such as: Electrodes,Nozzles, Swirl Rings, Retaining Caps, Shields and O-rings�

6� The Seller is not liable for damage of the Goods caused by the Buyer or third party by incorrect or 
unprofessional treatment of the Goods (in particular repair or alteration by persons not authorized 
by the Seller) or its installation, unprofessional usage of the Goods or insufficient maintenance, 
in particular using the Goods for other than the specified purpose or other failure to comply with 
operating instructions, application of excessive force or using unapproved consumables parts  
with the Goods�

Содержание EX-TRAFIRE 30H

























































Отзывы: