background image

P.25

Important Safety Precautions

# First time flyer should never fly by himself / herself.  Assistance from experienced flyer

   is absolutely necessary.

# Pre-flight adjustment must be done before flying, it is very dangerous to fly a badly

   pre-adjusted aircraft.

#                            is specially designed to be powered by 

KM28251025

 Outrunner Motor.

 

# Make sure the air field is spacious, never fly the plane too close to people and never get 

   too close to a running propeller.  Extreme caution should be exercised when working with 

   electric powered models.  Make sure the propeller is cleared of all objects, especially your 

   hands before connecting the battery to the model.  Make sure you understand the 

   operation of the ESC (Electronic Speed Control) by studying the ESC manual.  Once you 

   plug in the battery for electric powered model, always treat the propeller as a rotating one, 

   as accidental movement of the throttle stick will spin the propeller and could cause injuries.

# Check and re-tighten up all factory assembled screws, use thread locker if necessary.

Warning!

GM080PO30211403

Содержание SkyNova





























Отзывы: