THE ELECTRON MACHINE CORPORATION MPR E-SCAN Скачать руководство пользователя

Страница: 46 / 55

MPR

E-S

CAN

NFOR

MATION

5.1.2.3 Cable entry and mounting

The E-Scan console is set up to be mounted to a wall or other mounting device by the bracket

located on the bottom of the console. This also serves as a cable and power entry plate. It is

possible to change out the console without removing any wiring from the connectors. This can

be done by removing the cable connectors from the internal interface board along with the

screws holding the console to the mounting plate. Another method may be to utilize the stainless

steel connector option offered for the sensing head.

5.1.2.4 IB (interface board) for external connection

The interface board is located on the back wall of the console. Most external connections are

made to connectors that plug into this board. The only exceptions are optional features that

require connections to optional available connectors located on the side of the console.

5.1.2.5 Power supply

The power supply is located in the top of the console and serves as a hold down clamp for the

analog output modules. The power supply supplies power to both the I/O card and also the IB.

The voltages supplied are +5 vdc and +/- 15 vdc.

5.1.2.6 I/O card

The I/O card handles most of the signal inputs and outputs from the instrument. Two ribbon

cables route these signals from the IB to the I/O card and power is supplied through a power

cable from the power supply.

5-4

Содержание MPR E-SCAN
























































Результаты поиска

Содержание MPR E-SCAN

Отзывы:

Похожие инструкции для MPR E-SCAN

Бренды по названию

Популярные бренды

THE ELECTRON MACHINE CORPORATION MPR E-SCAN, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание MPR E-SCAN

Отзывы:

Похожие инструкции для MPR E-SCAN

Бренды по названию

Популярные бренды