IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USE
WARNING
– To reduce the risk of burns, electrocution, fire, or injury:
1.
Your vacuum cleaner is an electric appliance: it should be operated under normal conditions.
Basic precaution should always be followed to reduce the risk of fire, electrical shock, or injury
2. The following listed materials should not be suctioned up by the vacuum, otherwise it may damage the
appliance, cause fire, or injury to individuals.
a. Hot materials, such as cigarette and coal ashes.
b. Large pieces of materials which can block air openings or get stuck inside air flow chamber.
c. Poisonous, corrosive, or erosive materials (such as acids or detergent).
d. Any flammable or volatile liquid (such as gasoline or goods containing alcohol).
e. Excessive or large amounts of liquid, dirt or dust which could exceed the
“Maximum Dirt Level” line marked on the water container.
FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN ELECTRICAL SHOCK, FIRE,
DAMAGE TO THE PROPERTY OR SERIOUS PERSONAL INJURY AND EVEN DEAT H .
3. Do not place appliance where it can fall or be pulled into water or other liquid.
4. Do not reach for an appliance that has fallen into water. Unplug immediately!
5. Check all electrical wiring. Beware of damaged cord or plug.
6. This appliance is not intended for use by persons (including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for their safety.
7. This is not a toy. Children should be supervised to ensure that they do not play with the appliance.
8. Check that the main voltage corresponds to the voltage indicated on the rating label, see specifications
b e l o w :
ETL 120V 60Hz 1200W
GS 220-240V 50-60Hz 1200W
9.
Do not leave the appliance unattended while plugged in. Unplug from outlet when not in use and before
cleaning.
10. Avoid pulling or folding the hose, doing so may cause deformation or damage.
11. Use this appliance for its intended use as described in this manual. Do not use any other accessories or
attachments not recommended by the manufacturer. Doing so could result in fire, electrical shock, or
personal injury.
12. Never operate this appliance if it has a damaged cord or plug, if it is not working properly, if it has been
dropped or damaged, or dropped into water. If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
13. Do not pull, lift, or carry by the power cord. Do not use the cord as a handle, close a door on the cord,
or pull the cord around or against sharp edges or corners. Do not run vacuum over power cord.
U S E R ’ S G U I D E
U S E R ’ S G U I D E
2
9
Place the new or cleaned HEPA filter back into the machine, put the
HEPA filter cover back on, and lock the cover by pressing the clips.
Make sure the HEPA filter cover is securely in place. If cover is not
properly closed it will affect the suction power.
The HEPA filter should be cleaned or replaced every 4 months for
optimal performance. However this will depend on the frequency of use
and may need replacing more often. Clean the HEPA filter by gently
shaking it to remove accumulated dust/dirt, then wash it under cold
running water. The HEPA filter should not be washed with hot water or
any detergents. When removing dust and dirt do not use any brush or
other sharp objects that can cause damage. Let it completely dry before
inserting back into the vacuum. Note: Remember to empty water tank
before turning the unit upside down to avoid water spillage.
Important:
The filter should be cleaned after 5 to 6 times of usage
or if it is visibly dirty. The suction power will reduce if you do not
clean the filter frequently. When in operation, the filter should be
locked in place. The filter can be used after it is completely dry.
Check the filter to be sure it fits properly and is not damaged
before reusing.
Occasionally check and clean accumulated dirt on the rubber seal
around the air opening as illustrated. It is important to keep the
rubber seal clean, otherwise it can greatly affect suction power.
To remove the HEPA filter for cleaning or replacing, open the HEPA
cover and simply pull out the filter. Note: Empty water tank before
turning the unit upside down to avoid water spillage.
The HEPA filter is located at the bottom of the vacuum and is there to reduce dirt,
dust and particles from entering back into a room. Check the filter on a regular basis
as it will affect the suction power and smooth running of your vacuum.
To clean power head (optional item):
Remove the transparent cover by pulling it up from the base of the
power head. Remove all accumulated dirt and hair from bristle
roller. The transparent cover can be rinsed under running water,
let it dry before reinstalling.
Remove the small cover located on the bottom side of the power
head and clean any left dirt or hair.
HEPA filter