TFT Masterstream 4000 ER AUTOMATIC Скачать руководство пользователя страница 11

Страница: 11 / 16

©Copyright Task Force Tips LLC 2020

LIM-032 February 18, 2020 Rev00

7.0 FLUSHING DEBRIS

Debris in the water may get caught inside the nozzle. This trapped material will cause poor stream quality, shortened reach and
reduced

ow. To remove debris trapped in the nozzle:

1. Shut

ﬀ

ow to the nozzle

Move the stream shaper to the wide fog position.

Carefully unscrew and remove the ba

ﬄ

e and ori

ce control components

4. Remove/

ush debris

Reassemble the nozzle.

Figure 7.0 shows the pieces that are removed during the

ush procedure for automatic and selectable nozzles.

WARNING

Large amounts or pieces of debris may be un

ushable and can reduce the

ow of the nozzle

resulting in an ine

ﬀ

ective

ow. In the event of a blockage, it may be necessary to retreat to a safe

area, uncouple the nozzle and remove debris.

Selectable Nozzle

Automatic Nozzle

Baffle and

Orifice

Control

Components

Figure 7.0

Содержание Masterstream 4000 ER AUTOMATIC

















Результаты поиска

Содержание Masterstream 4000 ER AUTOMATIC

Отзывы:

Похожие инструкции для Masterstream 4000 ER AUTOMATIC

Бренды по названию

Популярные бренды

TFT Masterstream 4000 ER AUTOMATIC, Инструкции по безопасной эксплуатации и техническому обслуживанию

Результаты поиска

Содержание Masterstream 4000 ER AUTOMATIC

Отзывы:

Похожие инструкции для Masterstream 4000 ER AUTOMATIC

Бренды по названию

Популярные бренды