background image

©Copyright Task Force Tips  LLC  2020 

LIM-032 February 18, 2020 Rev00

MANUAL:  Masterstream 4000 ER
Automatic and Selectable Nozzles

INSTRUCTIONS FOR SAFE OPERATION AND MAINTENANCE

WARNING

Understand manual before use. Operation of this device without understanding the manual and 
receiving proper training is a misuse of this equipment. Obtain safety information at tft.com/ 
serialnumber.

This equipment is intended for use by trained and quali

fi

 ed emergency services personnel for 

fi

 re

fi

 ghting. All personnel using this equipment shall have completed a course of education 

approved by the Authority Having Jurisdiction (AHJ).

This instruction manual is intended to familiarize 

fi

 re

fi

 ghters and maintenance personnel with the 

operation, servicing, and safety procedures associated with this product. This manual should be 
kept available to all operating and maintenance personnel. 

TASK FORCE TIPS LLC

MADE IN USA • TFT.com

3701 Innovation Way, Valparaiso, IN 46383-9327 USA

800-348-2686 • 219-462-6161 • Fax 219-464-7155

AUTOMATIC

600 - 4000 gpm @ 80-120 psi

(2350 - 15,000 l/min @ 6 - 8 bar)

SELECTABLE

2000, 3000, 4000 gpm @ 100 psi

(7500, 11,000, 15,000 l/min @ 7 bar)

Содержание Masterstream 4000 ER AUTOMATIC

















Отзывы: