manualshive.com logo in svg

Textron JACOBSEN GP400, Техническое руководство по ремонту

Поделиться
Скачать
Textron JACOBSEN GP400 Скачать руководство пользователя страница 331

ACCESSORIES AND MISCELLANEOUS REPAIR

4252490-Rev A

9-19

9

Work Light

Removal and Installation

See Figure 9-41.

NOTE

Right work light is shown; left work light is similar.

1.

Park the mower safely. (See “Park Mower Safely” on 
page 1-6.)

2.

Disconnect the negative (–) battery cable from the 
battery.

Figure 9-41

NOTE

Label all wires before disconnecting to ensure correct 
installation.

3.

Disconnect wire connector (3).

4.

Remove nut (4), lock washer (5), and screw (6).

5.

Remove work light (1).

6.

To replace bulb, rotate bulb (2) counterclockwise at 
wire connector end, until bulb stops. Pull bulb straight 
out to remove.

Installation Notes

• Install work light bulb and work light by reversing the 

order of removal.

• Apply dielectric grease (Jacobsen PN 365422) to any 

wire connectors disconnected.

• Adjust work lights to project desired distance in front 

of the mower.

Front Wheel

Removal and Installation

See Figure 9-42.

1.

Park the mower safely. (See “Park Mower Safely” on 
page 1-6.)

2.

Block each side of rear wheel using suitable wheel 
blocks.

Figure 9-42

3.

Loosen, but do not remove, four mounting bolts (2).

!

WARNING

IMPORTANT

It is important to lift and support the machine, or the 
machine will move.

4.

Raise and support front of machine with jackstands.

5.

Remove four mounting bolts (2). 

6.

Remove wheel (1) and inspect tread area for tears or 
other damage.

7.

Replace tire if damage is excessive.

3

1

5

4

6

2

TN3660

• Support the machine using properly rated 

jackstands. Never work under a machine 
supported only by a jack.

• Do not use wood or concrete blocks to 

support the machine. Failure to properly 
support the machine may result in death or 
serious injury.

2

1

TN3721

Содержание JACOBSEN GP400



































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды