Textron Ezgo RXV-E Скачать руководство пользователя страница 38

Страница: 38 / 44

Customer Care

25108 Brake Sensor Error

Caused by: The brake pedal position sensor is out of operating range.

Verify the pedal stop bumper is in

the correct position. If not, correct and

secure in place.

Place pos. meter probe A on the

orange wire at the #3 position on the

controller plug. Place neg. probe B on

the black wire at the #4 position on the

controller plug. 5V should be observed.

If bad, check all 5V components first,

then

try a known good

controller. If good

go to step 3.

Place pos. meter probe A on the green

wire

of the brake position sensor and p

lace

neg. meter probe B on the black wire

the

brake

position sensor. Leave harness connected

to the sensor. Voltage should be between

0.3

V and 0.

V. If good, go to step 4. If bad,

verify harness.

Leave meter probes in place.

Slowly

epress the pedal to the floor. Voltage

should steadily increase from .5v to

between

4.5V

and 4.8V.

Above 4.8v is a fault.

If good

go to step 5. If bad, replace sensor.

5. Try a known good controller if error is gone

warranty controller. Error remains

reinstall

controller and contact Customer Care.

Page 3

Brake Pedal Bumper

Содержание Ezgo RXV-E













































Результаты поиска

Содержание Ezgo RXV-E

Отзывы:

Похожие инструкции для Ezgo RXV-E

Бренды по названию

Популярные бренды

Textron Ezgo RXV-E, Руководство по устранению неисправностей

Результаты поиска

Содержание Ezgo RXV-E

Отзывы:

Похожие инструкции для Ezgo RXV-E

Бренды по названию

Популярные бренды