Texmate, Inc. Tel. (760) 598-9899 • www.texmate.com
UM-35ACI Data Sheet (UM03)
Page 3
Decimal Point Selection
TB-Kit Screw Connectors
Optional PCB Edge Connector
Selecting Power Supply Voltages
Push-On Screw Terminals
Pinout Change-Over Connectors
Face Plate Descriptors
Custom Face Plates
L M N P R S
10 11 12 13 14 15
A
B
C
D
E
A
C
1
A
C
2
A
C
3
A
C
4
PCB BOARD : COMPONENT SIDE
L M N P R S
10 11 12 13 14 15
L M N P R S
10 11 12 13 14 15
A
B
C
D
E
A
C
1
A
C
2
A
C
3
A
C
4
PCB BOARD : COMPONENT SIDE
Joins
AC2 & 3
A
B
C
D
E
A
C
1
A
C
2
A
C
3
A
C
4
PCB BOARD : COMPONENT SIDE
N/C
With TB-KIT
Screw Terminals
With Optional
PCB Edge Connector
To customize the face plate, each
UM-meter is supplied with a white
printed clear adhesive label con-
taining various popular descriptors.
Choose the descriptor, peel off the
adhesive backing and align the
descriptor in the lower right corner
of the standard face plate.
A TB-KIT consists of 3 insulated
Quick Connects and 3 of Texmate’s
patented individual screw terminal
blocks which attach directly to PCB
inputs. These provide a Quick
Connect tab and screw clamp
termination. When using the TB-KIT
screw terminal blocks, it is possible to
select between 120V AC and 240V AC power, the optional low voltage
switching power supply or the 24V AC power supply by connecting the
screw terminals as shown in the diagrams below.
Six Screw Terminals included Free with each UM Series meter
Texmate’s exclusive optional Push-On Connectors combine an edge
card connector and a 10 position screw terminal block. Push-On
Connectors are ordered preconfigured for each specific power supply
voltage and each optional power supply available for the UM-Series.
A
1
2
3
4
5
6
7
8
9 10 11 12 13 14 15
B
C
D
E
F
H
K
J
L M N
P R
S
Rear View of PCB Edge Connector
A standard 30 pin edge connector (two rows of 15 pins on
0.156" centers) may also be used to connect the UM-Series.
Order part no. CN-L15. For different power supply voltage con-
nection details, see pin connections below.
For Isolated 9-36V DC/12-24V AC, 50/60 Hz
Switching Power Supply
For 200 to 240V AC, 50/60 Hz
or For Optional 24V AC (P.N.:V0-24V)
For 100 to 120V AC, 50/60 Hz
Hz
Milliamps AC
Volts AC
RPM
Volts DC
Kilowatts
kVAR
Millivolts AC
Kilovolts AC
Amps AC
pH
%
Millivolts DC
kg/cm
Watts
˚C
˚F
kWH
M/min
DC
µ
A
k
Amps DC
Milliamps DC
CosØ
m /hr
½
½
2
3
psi
Power Factor
They provide the greatest convenience and ease of use
M N P R
11 12 13 14
Top & bottom gold
fingers are joined on PCB
Join these pins
Join these pins
M N P R
11 12 13 14
Top & bottom gold
fingers are joined on PCB
M N P R
11 12 13 14
Top & bottom gold
fingers are joined on PCB
Pinouts are marked
on Connector
Connector can be
securely attached
to case with screws
Remove faceplate by inserting a screwdriver
blade in the slot at the bottom center of the face-
plate. Press blade in to release catch and gently
pry face plate outward from the bottom. (see also
Case Dimension drawing)
Decimal selection is made on the front of the dis-
play board by moving the jumper clip to the
desired position on the header.
Texmate Produces Thousands of
Custom OEM Face Plates
Have Texmate Design and produce a
Custom Face Plate for your next project!
• Custom face plates have a non-
recurring artwork charge. A serial
number is then assigned to each
artwork to facilitate reordering.
• Small Run or One-Off custom face plates incur an installation
charge, and are generally printed on a special plastic film, which is
then laminated to custom faceplate blanks as required.
• Large Run (250 pieces min): custom face plates are production
silk screened, issued a part number, and held in stock for free
installation as required by customer orders.
• OEMs may also order Custom Meter Labels, Box Labels, Custom
Data Sheets and Instruction Manuals.
To replace DPMs in existing panels where matching pinouts are
required, Texmate can provide custom pinout Change-over
Connectors, either with PCB gold finger terminations, (shown below)
or customized versions of Push-On Screw Terminals. (shown above)
Part Number
CN-UM/ANLGC
Change-over Connector
shown is for Analogic models
AN25M02,AN25M03,
AN25M04 and AN25M05.
1.XXX
1X.XX
1XX.X
1XXX.
Decimal
Select
Header
CN-PUSH/UM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100/120V AC
CN-PUSH/UM01 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200/240V AC
CN-PUSH/UM02 . . . . . . . . . . . . . . . . . . .Switch Selectable 120/240V AC
CN-PUSH/UM03 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24V AC
CN-PUSH/UM04 . . . . . . . . . . . . . . . . . . . . . . . . . . .9-36V DC/12-24V AC
CN-PUSH/UM05 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5V DC
