TEXIO DL-2060 Скачать руководство пользователя страница 115 | Manualshive

Страница: 115 / 152

background image

109

B.2 Output Data Formats

Output data will be in one of formats shown in the table below.

Type of Output Data

Non-reading queries
Single reading (GPIB)
Multiple readings (GPIB)

Output Data Format

< 80 ASCII character string
SD.DDDDDDDDESDD<nl>
SD.DDDDDDDDESDD,...,...,<nl>
SD.DDDDDDDDESDD<cr><nl>
SD.DDDDDDDDESDD,...,...,<cr><nl>

S

Negative sign or positive sign

D

Numeric digits

E

Exponent

<nl>

newline character

<cr>

carriage return character

B.3 The MEASure? Command

MEASure:VOLTage:DC? {<range>|MIN|MAX|DEF},{<resolution>|MIN|MAX|DEF}

Preset and make a dc voltage measurement with the specified range and resolution. The reading
is sent to the output buffer.

MEASure:VOLTage:DC:RATio? {<range>|MIN|MAX|DEF },{<resolution>|MIN|MAX|DEF}

Preset and make a dc:dc ratio measurement with the specified range and resolution. The reading
is sent to the output buffer. For ratio measurements, the specified range applies to input signal,
yet autorange is selected for the reference signal.

MEASure:VOLTage:AC? {<range>|MIN|MAX|DEF},{<resolution>|MIN|MAX|DEF}

Preset  and  make  an  AC  voltage  measurement  with  the  specified  range  and  resolution.  The
reading  is  sent  to  the  output  buffer.  For  AC  measurement,  resolution  is  fixed  at  6  ½  digits.
Therefore the resolution parameter only affects the front panel display.

MEASure:CURRent:DC? {<range>|MIN|MAX|DEF},{<resolution>|MIN|MAX|DEF}

Preset and make a dc current measurement with the specified range and resolution. The reading
is sent to the output buffer.

«
...
113
114
115
116
117
...
»

Содержание DL-2060

























































































































































Отзывы:

Нет отзывов

Похожие инструкции для DL-2060

Бренд: Keysight Technologies Страницы: 64

Intraplex STL-160 Series

Бренд: Harris Страницы: 178

OBID ID ISC.ANT.UMUX-A

Бренд: Feig Electronic Страницы: 30

Бренд: Cisco Страницы: 42

Бренд: Cisco Страницы: 24

Бренд: Cisco Страницы: 244

Бренд: Format Страницы: 101

Бренд: Eaton Страницы: 12

Бренд: Elma Страницы: 44

Бренд: Ohmeron Страницы: 17

Бренд: Wavetek Страницы: 32

Бренд: Ultra Stereo Labs Страницы: 12

Бренд: Harris Страницы: 157

Бренд: IDEAL Страницы: 6

Бренд: BK Precision Страницы: 2

Бренд: BK Precision Страницы: 9

Бренд: International Light Technologies Страницы: 17

Бренд: Conrad Electronic Страницы: 34

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды