Texas Instruments TRF7960, Руководство пользователя

Страница: 18 / 53

TRF7960
TRF7961
SLOU186F – AUGUST 2006 – REVISED AUGUST 2010 www.ti.com
Correlation between the RF input level and RSSI designation levels on the RX_IN1 and RX_IN2 are
shown in
Table 5-6 and Table 5-7 .
Table 5-6 shows the RSSI level versus RSSI bit value. The RSSI has seven levels (3 bits each) with 4-dB
increments. The input level is the peak-to-peak modulation level of the RF signal as measured on one side
envelope (positive or negative).
Table 5-6. RSSI Level Versus Register Bit Value
RSSI 1 2 3 4 5 6 7
Input level 2 mVpp 3.2 mVpp 5 mVpp 8 mVpp 13 mVpp 20 mVpp 32 mVpp
As an example, from Table 5-7 , let B2 = 1, B1 = 1, B0 = 0; this yields an RSSI value of 6. From Table 5-6
a Bit value of 6 would yield an RSSI level of 20 mVpp.
Table 5-7. RSSI Bit Value and Oscillator Status Register (0F)
Bit Signal Name Function Comments
B7 Unused
B6 osc_ok Crystal oscillator stable
B5 rssi_x2 MSB of auxiliary receiver RSSI
B4 rssi_x1 Auxiliary receiver RSSI
B3 rssi_x1 LSB of auxiliary receiver RSSI
4 dB per step
B2 rssi_2 MSB of main receiver RSSI
B1 rssi_1 Main receiver RSSI
B0 rssi_0 LSB of main receiver RSSI
5.2.2 Receiver
–
Digital Section
The received sub-carrier is digitized to form a digital representation of the modulated RF envelope. This
digitized signal is applied to digital decoders and framing circuits for further processing.
The digital part of the receiver consists of two sections, which partly overlap. The first section is the bit
decoders for the various protocols, whereas the second section consists of framing logic. The bit decoders
convert the sub-carrier coded signal to a bit stream and also to the data clock. Thus, the sub-carrier-coded
signal is transformed to serial data and the data clock is extracted. The decoder logic is designed for
maximum error tolerance. This enables the decoders to successfully decode even partly corrupted (due to
noise or interference) sub-carrier signals.
In the framing section, the serial bit-stream data is formatted in bytes. In this process, special signals like
the start of frame (SOF), end of frame (EOF), start of communication, and end of communication are
automatically removed. The parity bits and CRC bytes are checked and also removed. The end result is
clean or raw data, which is sent to the 12-byte FIFO register where it can be read by the external
microcontroller system.
The start of the receive operation (successfully received SOF) sets the flags in the IRQ and status
register. The end of the receive operation is indicated to the external system (MCU) by sending an
interrupt request (pin 13 IRQ). If the receive data packet is longer than 8 bytes, an interrupt is sent to the
MCU when the received data occupies 75% of the FIFO capacity to signal that the data should be
removed from the FIFO.
Any error in data format, parity, or CRC is detected, and the external system is notified of the error by an
interrupt-request pulse. The source condition of the interrupt-request pulse is available in the IRQ and
status register (address 0C). The bit-coding description of this register is given in
Table 5-22 .
18 System Description
Copyright © 2006 – 2010, Texas Instruments Incorporated
Submit Documentation Feedback
focus.ti.com: TRF7960 TRF7961