manualshive.com logo in svg

Texas Instruments TMS320C6A816 Series, Техническое справочное руководство


Поделиться
Скачать
background image

Preliminary

www.ti.com

Registers

2.4.9 DMM PAT View Mapping Base Address Register: DMM_PAT_VIEW_MAP_BASE

The MM PAT View Mapping Base Address register is shown and described in the figure and table below.

Figure 2-65. DMM_PAT_VIEW_MAP_BASE Register

31

30

0

BASEADDR

Reserved

R/W-0

R-0

LEGEND: R/W = Read/Write; R = Read only; -n = value after reset

Table 2-19. DMM_PAT_VIEW_MAP_BASE Register Field Descriptions

Bit

Field

Value

Description

Type

31

BASEADDR

0

MSB of the PAT view mapping base address

R/W

30-0

Reserved

0

Reserved

R

2.4.10 DMM PAT End of Interrupt Register: DMM_PAT_IRQ_EOI

The DMM PAT End of Interrupt register is shown and described in the figure and table below. This register
is per-event raw interrupt status vector. The purpose is mostly for debug. Raw status is set even if the
related event is not enabled. Write 1 to set the (raw) status.

Figure 2-66. DMM_PAT_IRQ_EOI Register

31

30

29

28

27

26

25

24

ERR_LUT_

ERR_UPD_

ERR_UPD_

ERR_UPD_

ERR_INV_

ERR_INV_

FILL_LST3

FILL_DSC3

MISS3

DATA3

CTRL3

AREA3

DATA3

DSC3

R/W1S-0

R/W1S-0

R/W1S-0

R/W1S-0

R/W1S-0

R/W1S-0

R/W1S-0

R/W1S-0

23

22

21

20

19

18

17

16

ERR_LUT_

ERR_UPD_

ERR_UPD_

ERR_UPD_

ERR_INV_

ERR_INV_

FILL_LST2

FILL_DSC2

MISS2

DATA2

CTRL2

AREA2

DATA2

DSC2

R/W1S-0

R/W1S-0

R/W1S-0

R/W1S-0

R/W1S-0

R/W1S-0

R/W1S-0

R/W1S-0

15

14

13

12

11

10

9

8

ERR_LUT_

ERR_UPD_

ERR_UPD_

ERR_UPD_

ERR_INV_

ERR_INV_

FILL_LST1

FILL_DSC1

MISS1

DATA1

CTRL1

AREA1

DATA1

DSC1

R/W1S-0

R/W1S-0

R/W1S-0

R/W1S-0

R/W1S-0

R/W1S-0

R/W1S-0

R/W1S-0

7

6

5

4

3

2

1

0

ERR_LUT_

ERR_UPD_

ERR_UPD_

ERR_UPD_

ERR_INV_

ERR_INV_

FILL_LST0

FILL_DSC0

MISS0

DATA0

CTRL0

AREA0

DATA0

DSC0

R/W1S-0

R/W1S-0

R/W1S-0

R/W1S-0

R/W1S-0

R/W1S-0

R/W1S-0

R/W1S-0

LEGEND: R/W = Read/Write; R = Read only; -n = value after reset

Table 2-20. DMM_PAT_IRQ_EOI Register Field Descriptions

Bit

Field

Value

Description

Type

31

ERR_LUT_MISS3

0

Unexpected Access to a yet-to-be-refilled area event in area 3

R/W1S

30

ERR_UPD_DATA3

0

Data register update whilst refilling error event in area 3

R/W1S

29

ERR_UPD_CTRL3

0

Control register update whilst refilling error event in area 3

R/W1S

28

ERR_UPD_AREA3

0

Area register update whilst refilling error event in area 3

R/W1S

27

ERR_INV_DATA3

0

Invalid entry-table pointer error event in area 3

R/W1S

26

ERR_INV_DSC3

0

Invalid descriptor pointer error event in area 3

R/W1S

25

FILL_LST3

0

End of refill event for the last descriptor in area 3

R/W1S

24

FILL_DSC3

0

End of refill event for any descriptor in area 3

R/W1S

23

ERR_LUT_MISS2

0

Unexpected Access to a yet-to-be-refilled area event in area 2

R/W1S

391

SPRUGX9 – 15 April 2011

DMM/TILER

Submit Documentation Feedback

© 2011, Texas Instruments Incorporated

Содержание TMS320C6A816 Series



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TMS320C6A816 Series

zipwake S Series Troubleshooting Manual preview
S Series
Бренд: zipwake Страницы: 12
Watts 7 Series Installation, Maintenance & Repair preview
7 Series
Бренд: Watts Страницы: 2
jbc UCR Instruction Manual preview
UCR
Бренд: jbc Страницы: 12
Fairchild 63 Installation, Operation And Maintenance Instructions preview
63
Бренд: Fairchild Страницы: 2
Fagor 101 Operating Manual preview
101
Бренд: Fagor Страницы: 103
Ohsung Electronics B905-FTN-TA User Manual preview
B905-FTN-TA
Бренд: Ohsung Electronics Страницы: 18
Abus FUMO50110 Quick Manual preview
FUMO50110
Бренд: Abus Страницы: 12
Daikin Maverick I Operation Manual preview
Maverick I
Бренд: Daikin Страницы: 48
Daikin MicroTech III Operating Manual preview
MicroTech III
Бренд: Daikin Страницы: 77
Daikin MicroTech III Operation And Maintenance Manual preview
MicroTech III
Бренд: Daikin Страницы: 32
Daikin BRC1E71 Engineeiring Data preview
BRC1E71
Бренд: Daikin Страницы: 46
Daikin MicroTech III Installation And Maintenance Manual preview
MicroTech III
Бренд: Daikin Страницы: 14
Daikin DCS601C51 Hardware Manual preview
DCS601C51
Бренд: Daikin Страницы: 16
Daikin BRC944B2 Quick User Manual preview
BRC944B2
Бренд: Daikin Страницы: 1
Paradox Grafica DNE-K07 Reference And Installation Manual preview
Grafica DNE-K07
Бренд: Paradox Страницы: 24
Panosol SR658 Operation Manuals preview
SR658
Бренд: Panosol Страницы: 105
Pangolin FB4 Series Quick Start Manual preview
FB4 Series
Бренд: Pangolin Страницы: 8
Samson 3372 User Manual preview
3372
Бренд: Samson Страницы: 8

Бренды по названию

Популярные бренды

Загрузить еще бренды