manualshive.com logo in svg

Texas Instruments TMS320C6A816 Series, Техническое справочное руководство


Поделиться
Скачать
background image

Preliminary

System Memory Map

www.ti.com

•

Each video capture port channel supports chroma down sampling (422 to 420) for any non-multiplexed
input data. The chroma down sampling for multiplexed streams is done as memory to memory
operations outside of HDVPSS on an individual frame data.

•

Deinterlacing is not supported in-line during capture.

•

Ancillary data capture is supported for VANC/VBI data (ancillary data within the interval between
SAV-EAV sequences during vertical blanking period) on all input channels. HANC data capture is NOT
supported. Decoding of the Ancillary data should be handled by the software.

•

Graphics overlay over incoming bitstream is NOT supported.

•

Noise Reduction on the incoming video is supported as a separate memory to memory operation
within the HDVPSS.

•

One of the 8-bit channels in each video port may be used as a video write back path for transcoding
applications. This channel may also use the color space conversion and/or the scaler. It is up to the
application to avoid resource contention.

Other Features

•

The HDVPSS supports 2 secondary video input sources in 420 tiled format used for memory-memory
operations (utilizing a scaler and chroma downsampler within one of the VIN ports in a memory to
memory configuration) with one of these ports capable of driving video to the SD output display. For
display output, there is no processing performed, i.e, no scaler or deinterlacing.

•

Only 1 of the 2 additional video input sources can directly drive the SD display. For display output,
there is no processing performed, ie, no scaler or deinterlacing.

•

The HDVPSS supports video data write back paths for following:

–

Scaled video from aux video channel saved as 422 video.

–

Scaled video from main video channel saved as 422 video.

–

Independently scaled video from main deinterlacer output (memory-to-memory scaling
application) – saved as a 420 video using the scaler and chroma_downsampler resources in one of
the VIN ports.

–

Independently scaled video from aux deinterlacer output (memory-to-memory scaling application) –
saved as a 420 video using the scaler and chroma_downsampler resources in the other VIN port.
This path is shared with the Secondary Inpput Path video input source.

–

Independently scaled video from the Secondary-1 and Secondary-2 video input source saved as a
420 video using a scaler and chroma downsampler resource in one of the VIN ports. These video
input sources can be 422 or 420 tiled input data (same as input for main and auxiliary inputs).
Secondary-1 and Secondary-2 video input source share the VIN write-back paths of the primary
and auxiliary deinterlacers.

–

Write back of the scaled video from main, aux or additional video input source video channels
supports both tightly (1 frame per 1 display frame period) and loosely (many frames per 1 display
frame period) coupled to the display frame period. All other write backs are tightly coupled

•

The HDVPSS includes a highly programmable and bandwidth efficient DMA controller to support the
worst case bandwidth application.

•

The HDVPSS performs compression and decompression on the TNR data from the main DEI and
private data from the auxiliary DEI to reduce overall bandwidth.

1.7

System Memory Map

For detailed specification on memory mapping, see the device-specific data manual.

170

Chip Level Resources

SPRUGX9 – 15 April 2011

Submit Documentation Feedback

© 2011, Texas Instruments Incorporated

Содержание TMS320C6A816 Series



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TMS320C6A816 Series

jbc DI Series Manual preview
DI Series
Бренд: jbc Страницы: 4
Eaton SC100 Operation Handbook preview
SC100
Бренд: Eaton Страницы: 86
MADRIX AURA Technical Manual & Quick Start Manual preview
AURA
Бренд: MADRIX Страницы: 36
JDS Uniphase SK Series User Manual preview
SK Series
Бренд: JDS Uniphase Страницы: 27
Danfoss EH Series Service Manual preview
EH Series
Бренд: Danfoss Страницы: 20
OEG KMS Manual preview
KMS
Бренд: OEG Страницы: 168
BADODOSECURITY G200 Quick Manual preview
G200
Бренд: BADODOSECURITY Страницы: 8
ECKELMANN VS 3010 BS Operating Instruction preview
VS 3010 BS
Бренд: ECKELMANN Страницы: 178
GARAN EWS-102 Calibration & Setup preview
EWS-102
Бренд: GARAN Страницы: 8
Gamma Vacuum SPCe User Manual preview
SPCe
Бренд: Gamma Vacuum Страницы: 25
Gamma DIGITEL MPCq User Manual preview
DIGITEL MPCq
Бренд: Gamma Страницы: 28
Gascat ARGOS Installation, Operation & Maintenance Manual preview
ARGOS
Бренд: Gascat Страницы: 32
Water Furnace IntelliZone2 MasterStat Specification Catalog And Design Manual preview
IntelliZone2 MasterStat
Бренд: Water Furnace Страницы: 44
Comparato Compamix PR Instruction Manual preview
Compamix PR
Бренд: Comparato Страницы: 20
Valence Tech iBT-07 Manual preview
iBT-07
Бренд: Valence Tech Страницы: 12
Dungs 273061 Instructions Manual preview
273061
Бренд: Dungs Страницы: 56
Emec PH CONTROLLER Operating Manual preview
PH CONTROLLER
Бренд: Emec Страницы: 8
Dickey-John Control Point Operator'S Manual preview
Control Point
Бренд: Dickey-John Страницы: 109

Бренды по названию

Популярные бренды

Загрузить еще бренды