Главная
/
Texas Instruments
/
TMS320C6670
/
Руководство по данным

Texas Instruments TMS320C6670, Руководство по данным

Поделиться

Страница: 118 / 226

background image

118

TMS320C6670 Peripheral Information and Electrical Specifications

Copyright 2012 Texas Instruments Incorporated

SPRS689D—March 2012

Multicore Fixed and Floating-Point System-on-Chip

TMS320C6670

Submit Documentation Feedback

7.3.2 Clock Domains

Clock gating to each logic block is managed by the local power/sleep controllers (LPSCs) of each module. For
modules with a dedicated clock or multiple clocks, the LPSC communicates with the PLL controller to enable and
disable that module's clock(s) at the source. For modules that share a clock with other modules, the LPSC controls
the clock gating.

shows the TMS320C6670 clock domains.

Table 7-7

Clock Domains

LPSC Number

Module(s)

Notes

0

Shared LPSC for all peripherals other than those listed in this table

Always on

1

SmartReflex

Always on

2

DDR3 EMIF

Always on

3

TCP3e

Software control

4

VCP2_A

Software control

5

Debug subsystem and tracers

Software control

6

Per-core TETB and system TETB

Software control

7

Packet Accelerator

Software control

8

Ethernet SGMIIs

Software control

9

Security Accelerator

Software control

10

PCIe

Software control

11

SRIO

Software control

12

HyperLink

Software control

13

Reserved

Reserved

14

MSMC RAM

Software control

15

RAC_A and RAC_B

Software control

16

TAC

Software control

17

FFTC_A and FFTC_B

Software control

18

AIF2

Software control

19

TCP3d_A

Software control

20

VCP2_B

Software control

21

VCP2_C

Software control

22

VCP2_D

Software control

23

C66x CorePac0 and Timer0

Always on

24

C66x CorePac1 and Timer1

Always on

25

C66x CorePac1 RSAs

Software control

26

C66x CorePac2 and Timer2

Always on

27

C66x CorePac2 RSAs

Software control

28

C66x CorePac3 and Timer3

Always on

29

TCP3d_B

Software control

30

BCP, FFTC_C, and TCP3d_C

Software control

No LPSC

Bootcfg, PSC, and PLL Controller

These modules do not use LPSC

End of Table 7-7

«
...
116
117
118
119
120
...
»

Содержание TMS320C6670



































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TMS320C6670

Бренд: Samson Страницы: 92

Бренд: Jafar Страницы: 10

Бренд: Hach Страницы: 2

Бренд: Hach Страницы: 12

Бренд: Hach Страницы: 472

Бренд: Hach Страницы: 64

Бренд: V2 ELETTRONICA Страницы: 6

Бренд: Hach Страницы: 210

Бренд: Oldham Страницы: 32

Бренд: H3C Страницы: 14

Slim Remote Control

Бренд: Packard Bell Страницы: 2

Бренд: Unipower Страницы: 24

Бренд: RAKwireless Страницы: 6

Бренд: YOKOGAWA Страницы: 150

Бренд: YOODA Страницы: 3

Бренд: YMGI Страницы: 8

Бренд: CAME Страницы: 2

Бренд: ZKTeco Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды