manualshive.com logo in svg

Texas Instruments TMS320C645X, Руководство пользователя


Поделиться
Скачать
background image

www.ti.com

SRIO Functional Description

So the general flow is as follows:

•

Previously, the control/command registers were written and the request packet was sent

•

Response Packet Type13, Trans != 0001b arrives at module interface, and is handled sequentially (not
based on priority)

•

targetTID is examined to determine routing of a response to the appropriate core

•

The status field of the response packet is checked for ERROR, RETRY or DONE

•

If the field is DONE, it submits DMA bus request and transmits the payload (if any) to DSP address. If
the field is ERROR/RETRY, it sets an interrupt

•

Command registers are released (BSY = 0)

•

Optional Interrupt to CPU notifying packet reception

2.3.3.4

Reset and Power Down State

Upon reset, the Load/Store module must clear the command register fields and wait for a write by the
CPU.

The Load/Store module can be powered down if the direct I/O protocol is not being supported in the
application. For example, if the messaging protocol is being used for data transfers, powering down the
Load/Store module will save power. In this situation, the command registers should be powered down and
inaccessible. Clocks should be gated to these blocks while in the power down state.

2.3.4

Message Passing

With message passing, a destination address is not specified. Instead, a mailbox identifier is used within
the RapidIO packet. The mailbox is controlled and mapped to memory by the local (destination) device.
The message passing within RapidIO specifies 4 mailbox locations. Each mailbox can contain 4 separate
transactions (or letters), effectively providing 16 messages. Single packet messages provide 64 mailboxes
with 4 letters, effectively providing 256 messages. Mailboxes can be defined for different data types or
priorities. The advantage of message passing is that the source device does not require any knowledge of
the destination device’s memory map. The DSP contains Buffer Descriptions Tables for each mailbox.
These tables define a memory map and pointers for each mailbox. Messages are transferred to the
appropriate memory locations via the DMA.

The CPPI (Communications Port Programming Interface) module serves as the incoming and outgoing
message passing protocol engine.

The following rules exist for all CPPI traffic:

•

One buffer descriptor per message (each buffer descriptor consists of 4 words or 16 bytes)

•

Requires contiguous memory space for multi-segment Read/Write operations

–

Fixed buffer sizes (configured to handle application's max message size)

•

An ERROR response is sent if the RX message is too big for the allotted buffer sizes

–

Subsequent ERROR responses will be sent for all segments of that message

•

An ERROR response is sent if the mailbox is not mapped, or mapped to a non-existent queue

•

An ERROR response is sent if the mailbox is mapped, but the queue is not initialized (RX DMA State
HDP not written), or the queue is disabled (Teardown)

•

An ERROR response is sent if the RX buffer descriptor queue has no empty buffers (overflow)

•

Out-of-order responses are allowed

•

RETRY response will be issued to the first received segment of a multi-segment message when the
RX queue is busy servicing another request

–

Subsequent RETRY responses may have to be sent for received pipeline segments or additional
pipelined messages to the same queue

•

Inorder message reception for dedicated flows is mode programmable

•

A queue is needed for each supported simultaneous multi-segment RX message

•

Supports a minimum of 1.25KB SRAM (64 buffer descriptors)

•

Transmit must be able to RETRY any given segment of a transmitted message

•

A Dest_id is equal to port for TX operations, the same Dest_Id is not accessible from multiple ports

40

Serial RapidIO (SRIO)

SPRU976 – March 2006

Submit Documentation Feedback

Содержание TMS320C645X



























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TMS320C645X

Rachio IRO Installation Manual preview
IRO
Бренд: Rachio Страницы: 2
Ultraflex B47 Installation Instructions Manual preview
B47
Бренд: Ultraflex Страницы: 7
Desoutter 6159326760 Original Instructions Manual preview
6159326760
Бренд: Desoutter Страницы: 74
AUMA VARIOMATIC SARV 07.1 Operation Instructions Manual preview
VARIOMATIC SARV 07.1
Бренд: AUMA Страницы: 32
Neets Control LiMa Installation Manual preview
LiMa
Бренд: Neets Control Страницы: 12
National Instruments sbRIO-9698 User Manual preview
sbRIO-9698
Бренд: National Instruments Страницы: 12
Evco EVCLC229N9E Manual preview
EVCLC229N9E
Бренд: Evco Страницы: 78
DOM DOM Tapkey Access Manager V1 Assembly And Operating Instructions Manual preview
DOM Tapkey Access Manager V1
Бренд: DOM Страницы: 118
Samson TROVIS 5724-8 Mounting And Operating Instructions preview
TROVIS 5724-8
Бренд: Samson Страницы: 64
Kemper 689 04 011 Service Manual preview
689 04 011
Бренд: Kemper Страницы: 16
RKC INSTRUMENT REX-C100 Instruction Manual preview
REX-C100
Бренд: RKC INSTRUMENT Страницы: 8
Suzhou MONARCH Control Technology Co., Ltd. NICE3000 New User Manual preview
NICE3000 New
Бренд: Suzhou MONARCH Control Technology Co., Ltd. Страницы: 233
National Instruments PXI Series User Manual preview
PXI Series
Бренд: National Instruments Страницы: 88
IEI Technology TANK-870-Q170-QGW Quick Installation Manual preview
TANK-870-Q170-QGW
Бренд: IEI Technology Страницы: 4
X10 PHC01 Owner'S Manual preview
PHC01
Бренд: X10 Страницы: 4
A.B.S. 23023 Quick Start Manual preview
23023
Бренд: A.B.S. Страницы: 5
Vivo DESK-V103EW Instruction Manual preview
DESK-V103EW
Бренд: Vivo Страницы: 4
KMC Controls CSP-4702 Installation Manual preview
CSP-4702
Бренд: KMC Controls Страницы: 4

Бренды по названию

Популярные бренды

Загрузить еще бренды