manualshive.com logo in svg

Texas Instruments TMS320 2806 Series, Техническое справочное руководство


Поделиться
Скачать
background image

3.4.8.5 Digital Compare Capture Control (DCCAPCTL) Register

Figure 3-111. Digital Compare Capture Control (DCCAPCTL) Register

15

8

Reserved

R-0

7

2

1

0

Reserved

SHDWMODE

CAPE

R-0

R/W-0

R/W-0

LEGEND: R/W = Read/Write; R = Read only; -

n

 = value after reset

Table 3-60. Digital Compare Capture Control (DCCAPCTL) Register Field Descriptions

Bit

Field

Value

Description

15-2

Reserved

Reserved

1

SHDWMODE

TBCTR Counter Capture Shadow Select Mode

0

Enable shadow mode. The DCCAP active register is copied to shadow register on a TBCTR = 
TBPRD or TBCTR = zero event as defined by the DCFCTL[PULSESEL] bit. CPU reads of the 
DCCAP register will return the shadow register contents.

1

Active Mode. In this mode the shadow register is disabled. CPU reads from the DCCAP register will 
always return the active register contents.

0

CAPE

TBCTR Counter Capture Enable/Disable

0

Disable the time-base counter capture.

1

Enable the time-base counter capture.

Enhanced Pulse Width Modulator (ePWM) Module

www.ti.com

372

TMS320x2806x Microcontrollers

SPRUH18I – JANUARY 2011 – REVISED JUNE 2022

Submit Document Feedback

Copyright © 2022 Texas Instruments Incorporated

Содержание TMS320 2806 Series






















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TMS320 2806 Series

Lawler 804 Installation & Maintenance Manual preview
804
Бренд: Lawler Страницы: 5
Vent-Axia SAC 5 Installation And Wiring Instructions preview
SAC 5
Бренд: Vent-Axia Страницы: 4
Lumel re72 series Quick Start Manual preview
re72 series
Бренд: Lumel Страницы: 32
JBSYSTEMS Light SCENE MASTER - V1.0 Operation Manual preview
SCENE MASTER - V1.0
Бренд: JBSYSTEMS Light Страницы: 24
CALEFFI AIR190002 Quick Start Manual preview
AIR190002
Бренд: CALEFFI Страницы: 14
OCL DLC-1.1 Quick Start Manual preview
DLC-1.1
Бренд: OCL Страницы: 2
Galcon DC-11SF Installation And Operating Instructions Manual preview
DC-11SF
Бренд: Galcon Страницы: 24
NXP Semiconductors freescale Kinetics TWR-K60N512-KEIL Quick Start Manual preview
freescale Kinetics TWR-K60N512-KEIL
Бренд: NXP Semiconductors Страницы: 5
Trio MC206X Quick Connection Manual preview
MC206X
Бренд: Trio Страницы: 8
Dawn CONTROL-1500A Manual preview
CONTROL-1500A
Бренд: Dawn Страницы: 100
Atkinson Electronics PVLC-40MD Quick Start Manual preview
PVLC-40MD
Бренд: Atkinson Electronics Страницы: 3
Elimko E-70-O User Manual preview
E-70-O
Бренд: Elimko Страницы: 2
Danfoss AME 85 QM Operating Manual preview
AME 85 QM
Бренд: Danfoss Страницы: 16
NTI AG LinMot E1200 Series Installation Manual preview
LinMot E1200 Series
Бренд: NTI AG Страницы: 20
Magnetek GPD 333 Technical Manual preview
GPD 333
Бренд: Magnetek Страницы: 81
Festo LRP-1/4 Series Operating Instructions Manual preview
LRP-1/4 Series
Бренд: Festo Страницы: 16
Pentair Goyen IS Series Products Installation Instructions preview
Goyen IS Series
Бренд: Pentair Страницы: 6
V2 STARK6 Manual preview
STARK6
Бренд: V2 Страницы: 64

Бренды по названию

Популярные бренды

Загрузить еще бренды