manualshive.com logo in svg

Texas Instruments TMS320 2806 Series, Техническое справочное руководство


Поделиться
Скачать
background image

17.5.52 USB Device RESUME Interrupt Status and Clear Register (USBDRISC), offset 0x418

The USB device RESUME interrupt status and clear register (USBDRRIS) is the raw interrupt clear register. On 
a write of 1, the corresponding interrupt is cleared. A write of 0 has no effect.

Mode(s):

Host

Device

USBDRISC is shown in 

Figure 17-64

 and described in 

Table 17-67

.

Figure 17-64. USB Device RESUME Interrupt Status and Clear Register (USBDRISC)

31

1

0

Reserved

RESUME

R-0

R/W1C

LEGEND: R/W = Read/Write; R = Read only; -

n

 = value after reset

Table 17-67. USB Device RESUME Interrupt Status and Clear Register (USBDRISC) Field Descriptions

Bit

Field

Value

Description

31-1

Reserved

0

Reserved. Reset is 0x0000.000.

0

RESUME

RESUME Interrupt Status and Clear.
This bit is cleared by writing a 1. Clearing this bit also clears the RESUME bit in the USBDRCRIS 
register.

0

The RESUME bits in the USBDRRIS and USBDRCIM registers are set, providing an interrupt to the 
interrupt controller.

1

No interrupt has occurred or the interrupt is masked.

www.ti.com

Universal Serial Bus (USB) Controller

SPRUH18I – JANUARY 2011 – REVISED JUNE 2022

Submit Document Feedback

TMS320x2806x Microcontrollers

1135

Copyright © 2022 Texas Instruments Incorporated

Содержание TMS320 2806 Series






















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TMS320 2806 Series

ZKTeco F6 Installation Manual preview
F6
Бренд: ZKTeco Страницы: 2
FASAR ELETTRONICA FE230 Quick Start Manual preview
FE230
Бренд: FASAR ELETTRONICA Страницы: 2
Faro 33928 Installation Manual preview
33928
Бренд: Faro Страницы: 3
YASKAWA G7 Series Technical Manual preview
G7 Series
Бренд: YASKAWA Страницы: 456
Gardena EasyPlus Operator'S Manual preview
EasyPlus
Бренд: Gardena Страницы: 14
Gardena 1273 Operating Instructions preview
1273
Бренд: Gardena Страницы: 4
Gantner GAT ACCESS 6100 User Manual preview
GAT ACCESS 6100
Бренд: Gantner Страницы: 4
Hanna Instruments HI 8001 Instruction Manual preview
HI 8001
Бренд: Hanna Instruments Страницы: 88
Eaton FC18 User Manual preview
FC18
Бренд: Eaton Страницы: 10
PENGWYN 485-1P-JS Technical Manual preview
485-1P-JS
Бренд: PENGWYN Страницы: 32
Warner Electric CBC-801-1 Installation Instructions And Service Manual preview
CBC-801-1
Бренд: Warner Electric Страницы: 6
Teledyne Foxy R1 Instruction Manual preview
Foxy R1
Бренд: Teledyne Страницы: 102
Sartorius PR 5610 Installation Manual preview
PR 5610
Бренд: Sartorius Страницы: 165
Mosa EAS 15-806 Use And Maintenance Manual preview
EAS 15-806
Бренд: Mosa Страницы: 28
SEW MOVIFIT SC series Operating Instructions Manual preview
MOVIFIT SC series
Бренд: SEW Страницы: 148
Eclipse TRILOGY T500 Series Instruction Manual preview
TRILOGY T500 Series
Бренд: Eclipse Страницы: 20
Window Master MotorController WCC 310 UL Installation Instructions Manual preview
MotorController WCC 310 UL
Бренд: Window Master Страницы: 39
mikroElektronika mikromedia for ARM User Manual preview
mikromedia for ARM
Бренд: mikroElektronika Страницы: 35

Бренды по названию

Популярные бренды

Загрузить еще бренды