background image

EVM User’s Guide 

TI Confidential – Strictly Private 

 

24 

 

PROVIDED HEREUNDER, EXCEED THE TOTAL AMOUNT PAID TO TI FOR THE PARTICULAR UNITS SOLD UNDER 
THESE TERMS AND CONDITIONS WITH RESPECT TO WHICH LOSSES OR DAMAGES ARE CLAIMED. THE EXISTENCE 
OF MORE THAN ONE CLAIM AGAINST THE PARTICULAR UNITS SOLD TO USER UNDER THESE TERMS AND 
CONDITIONS SHALL NOT ENLARGE OR EXTEND THIS LIMIT. 
9. 

Return Policy. 

Except as otherwise provided, TI does not offer any refunds, returns, or exchanges. Furthermore, no return of 

EVM(s) 
will be accepted if the package has been opened and no return of the EVM(s) will be accepted if they are damaged or otherwise not 
in 
a resalable condition. If User feels it has been incorrectly charged for the EVM(s) it ordered or that delivery violates the applicable 
order, User should contact TI. All refunds will be made in full within thirty (30) working days from the return of the components(s), 
excluding any postage or packaging costs. 
10. 

Governing Law: 

These terms and conditions shall be governed by and interpreted in accordance with the laws of the State of 

Texas, 
without reference to conflict-of-laws principles. User agrees that non-exclusive jurisdiction for any dispute arising out of or relating to 
these terms and conditions lies within courts located in the State of Texas and consents to venue in Dallas County, Texas. 
Notwithstanding the foregoing, any judgment may be enforced in any United States or foreign court, and TI may seek injunctive 
reliefin any United States or foreign court. 
 

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 

Copyright © 2014, Texas Instruments Incorporated 

spacer

 

 

 

 

Содержание CC3100MOD Boosterpack
























Отзывы: