Texas Instruments bq24260 Скачать руководство пользователя страница 1

Страница: 1 / 25

User's Guide

SLUUAV8A – February 2014 – Revised August 2014

User's Guide for QFN Packaged bq24260, bq24261, and

bq24262 3-A Battery Charger Evaluation Module

The bq24260, bq24261, and bq24262 evaluation module on the printed-circuit board (PCB) PWR611 is a
complete charger module for evaluating a compact, flexible, high-efficiency, USB-friendly, switch-mode
charge management solution for single-cell, Li-ion and Li-polymer batteries used in a wide range of
portable applications.

Contents

Introduction

...................................................................................................................

1.1

bq2416x IC Features

...............................................................................................

1.2

bq24260, bq24261, bq24262 EVM Features

....................................................................

1.3

Schematic

............................................................................................................

1.4

I/O Description

......................................................................................................

1.5

Test Points

...........................................................................................................

1.6

Control and Key Parameters Setting

.............................................................................

1.7

Recommended Operating Conditions

............................................................................

Test Summary

................................................................................................................

2.1

Definitions

............................................................................................................

2.2

Recommended Test Equipment

..................................................................................

2.3

Recommended Test Equipment Setup

..........................................................................

2.4

Recommended Test Procedure

.................................................................................

Printed-Circuit Board Layout Guideline

..................................................................................

Bill of Materials and Board Layout

......................................................................................

4.1

Bill of Materials

....................................................................................................

4.2

Board Layout

.......................................................................................................

List of Figures

bq24260, bq24261, bq24262EVM Schematic

...........................................................................

BAT_Load (PR1010) Schematic

...........................................................................................

Connections of HPA172 Kit

................................................................................................

Original Test Setup for bq24260, bq24261, bq24262 EVM

............................................................

Main Window of the bq2426xSW Evaluation Software

................................................................

Top Assembly Layer

.......................................................................................................

Top Layer

...................................................................................................................

First Internal Layer

.........................................................................................................

Second Internal Layer

.....................................................................................................

Bottom Layer

................................................................................................................

List of Tables

Bill of Materials - PWR611

................................................................................................

SLUUAV8A – February 2014 – Revised August 2014

User's Guide for QFN Packaged bq24260, bq24261, and bq24262 3-A

Battery Charger Evaluation Module

Submit Documentation Feedback

Содержание bq24260


























Результаты поиска

Содержание bq24260

Отзывы:

Похожие инструкции для bq24260

Бренды по названию

Популярные бренды

Texas Instruments bq24260, Руководство пользователя

Результаты поиска

Содержание bq24260

Отзывы:

Похожие инструкции для bq24260

Бренды по названию

Популярные бренды