Texas Instruments BQ24180, Руководство пользователя

Страница: 13 / 15

www.ti.com
Schematic, Board Layouts, and Bill of Materials
5.3 Bill of Materials
Table 1. Bill of Materials for bq24180EVM
Count RefDes Value Description Size Part Number MFR
3 C1, C2, C7 1 µ F Capacitor, Ceramic, Low Inductance, 10V, X5R, 10% 0603 ECJ-1VB1A105K Panasonic
2 C9, C10 10 µ F Capacitor, Ceramic, 10V, X5R, 10% 0805 ECJ-2FB1A106K Panasonic
1 C3 1 µ F Capacitor, Ceramic, X5R, 16V, ± 10% 0603 ECJ-1VB1C105K Panasonic
2 C4, C6 0.1 µ F Capacitor, Ceramic, Low Inductance, 16V, X7R, 10% 0603 ECJ-1VB1C104K Panasonic
1 C5 0.01 µ F Capacitor, Ceramic, Low Inductance, 25V, X7R, 10% 0603 ECJ-1VB1E103K Panasonic
1 C8 4.7 µ F Capacitor, Ceramic, 16V, X5R, 10% 0805 ECJ-2FB1C475K Panasonic
1 D1 BZX84C6V2W Diode, Zener, 6.2-V, 200-mW SOT-323 BZX84C6V2W Diodes
1 D2 Green Diode, LED, Green, 2.1-V, 20-mA, 6-mcd 0603 LTST-C190GKT-7-F Lite On
3 J1, J2, J3 ED555/2DS Terminal Block, 2-pin, 6-A, 3.5mm 0.27 x 0.25 inch ED555/2DS OST
1 J4 Connector, Male Straight 2x5 pin, 100mil spacing, 4 Wall 0.338 x 0.788 inch N2510-6002-RB 3M
1 J5 ED555/3DS Terminal Block, 3-pin, 6-A, 3.5mm 0.41 x 0.25 inch ED555/3DS OST
1 J6 ED555/4DS Terminal Block, 4-pin, 6-A, 3.5mm 0.55 x 0.25 inch ED555/4DS OST
4 JMP1, JMP2, PEC03SAAN Header, Male 3-pin, 100mil spacing, 0.100 inch x 3 PEC03SAAN Sullins
JMP3, JMP4
1 L1 1.0 µ H Inductor, SMT, 1.5A, 80milliohm, ± 30% 2.5 x 2.0 mm LQM2HPN1R0MJ0 or Murata or
MIPS2520D1R0 or FDK or
MDT2520-CN1R0M or TOKO or
CP1008 Inter-Technical
1 R1 4.99k Resistor, Chip, 1/16W, 1% 0603 Std Std
1 R2 4.7k Resistor, Chip, 1/16W, 1% 0603 Std Std
1 R3 100k Resistor, Chip, 1/16W, 1% 0603 Std Std
1 R4 0.068 Resistor, Chip, 1/10W, 1% 0805 Std Std
1 R5 1.5k Resistor, Chip, 1/16-W, 5% 0603 Std Std
2 R6, R7 200 Resistor, Chip, 1/16W, 1% 0603 Std Std
0 TP1 thru TP7 STD Test Point, 0.020 Hole "
1 TP8 5001 Test Point, Black, Thru Hole Color Keyed 0.100 x 0.100 inch 5001 Keystone
1 TP9 5000 Test Point, Red, Thru Hole Color Keyed 0.100 x 0.100 inch 5000 Keystone
1 U1 BQ24180YFF IC, Fully Integrated Switch-Mode One-Cell Li-Ion Charger with WCSP BQ24180YFF TI
Full USB Compliance
1 — PCB, 2 In x 2 In x 0.031 In HPA478 Any
4 929950-00 Shunts 100 mill 929950-00 3M
Notes: 1. These assemblies are ESD sensitive, ESD precautions shall be observed.
2. These assemblies must be clean and free from flux and all contaminants. Use of no clean flux is not acceptable.
3. These assemblies must comply with workmanship standards IPC-A-610 Class 2.
4. Ref designators marked with an asterisk ( ' ** ' ) cannot be substituted. All other components can be substituted with equivalent MFG ' s components.
5. Installed jumpers JMP1-2/3 (CD, GND); JMP2-1/2 (PSEL, HI); JMP3-1/2 (LED); JMP4-2/3 (TS_4.7k, GND)
13 SLUU419A – April 2010 – Revised April 2011 bq24180 Evaluation Module
Submit Documentation Feedback
Copyright © 2010 – 2011, Texas Instruments Incorporated