Texas Instruments BOOST-PSEMTHR8-097 Скачать руководство пользователя страница 5

Страница: 5 / 34

TPS237 3-4EVM-758

Class 3-4

Positive

Power

Sup ply

TPS238 82EVM-008

)

(

)

USB2ANY

BOO ST-PSE MTHR-097

Ribbon

Cable

xxx

USB CABLE

Etherne t

Cable

Negative

www.ti.com

Quick Start

SLVUBQ3 – August 2019

Submit Documentation Feedback

TPS23882EVM: PoE, PSE, TPS23882 Evaluation Module

2.5

Basic Test Setup Using USB2ANY for I

C Interface (Auto Mode or Semi-Auto Mode

Operation with I

C Monitoring)

An I

C interface is provided through J2 of the mother board to the TPS23882 device on the

TPS23882EVM-008. The USB2ANY adapter (not included) can be used with any TI GUI which uses
USB2ANY to read and write over an I

C bus.

Figure 2

illustrates the basic setup using USB2ANY.

Figure 2. Basic Setup Using USB2ANY

CAUTION

If wanting to run TPS23882 in semi auto mode, remove the jumper installed on
J5 of the TPS23882 daughter board before powering on the board.

Содержание BOOST-PSEMTHR8-097



































Результаты поиска

Содержание BOOST-PSEMTHR8-097

Отзывы:

Похожие инструкции для BOOST-PSEMTHR8-097

Бренды по названию

Популярные бренды

Texas Instruments BOOST-PSEMTHR8-097, Руководство пользователя

Результаты поиска

Содержание BOOST-PSEMTHR8-097

Отзывы:

Похожие инструкции для BOOST-PSEMTHR8-097

Бренды по названию

Популярные бренды