Texas Instruments ADS54J64 Скачать руководство пользователя страница 9

Страница: 9 / 24

www.ti.com

Quick Start Guide

SBAU290 – September 2017

Submit Documentation Feedback

ADS54J64 Evaluation Module

2.4

Quick Start Troubleshooting

Table 2

lists tips which can be used to assist with problems that may have occurred during the quick start

procedure.

Table 2. Troubleshooting Tips

Issue

Troubleshooting Tips

General problems

Verify the test setup shown in

Figure 2

, and repeat the setup procedure

as described in this document.

Check power supplies to the EVM and TSW14J56EVM. Verify that the
power switches are in the ON position.

Check signal and clock connections to the EVM.

Check that all boards are properly connected together.

Try pressing the CPU_RESET button on the TSW14J56EVM.

Try power-cycling the external power supply to the EVM and reprogram
the LMK and ADC devices.

TSW14J56 LEDs are incorrect:
D1, D5 – N/A
D2, D4 – Flashing
D3, D6, D7 – OFF
D8, D28 – ON

Verify the settings of the configuration switches on the TSW14J56EVM.

Verify that the EVM configuration GUI is communicating with the USB,
and that the configuration procedure was followed.

LEDs not flashing – reprogram the LMK device.

Try pressing the CPU_RESET button on the TSW14J56EVM.

Try capturing data in HSDC Pro to force an LED status update.

Device GUI is not working properly.

Verify that the USB cable is plugged into the EVM and the PC.

Check the Device Manager of the computer, and verify that a

USB Serial

Device

is recognized when the EVM is connected to the PC.

Verify that the green

USB Status

LED light in the top-right corner of the

GUI is lit. If the LED is not lit, press the Reconnect FTDI button.

Try restarting the configuration GUI.

Check default jumper connections as shown in

Appendix A

HSDC Pro Software is not capturing good data or
analysis results are incorrect.

Verify that the TSW14J56EVM is properly connected to the PC with a
mini-USB cable, and that the board serial number is properly identified by
the HSDC Pro software.

Check that the proper ADC device is selected. In default conditions,

ADS54J64_LMF_4841_mode01

must be selected.

Check that the analysis parameters are properly configured.

HSDC Pro Software gives a time-out error when
capturing data.

Try to reprogram the LMK device and reset the JESD204 Link.

Verify that the ADC sampling rate is correct in the HSDC Pro software.

Sub-optimal measured performance

Try pressing the Calibrate ADC button on the INTRO tab, to repeat the
configuration GUI procedure for programming the EVM

Check that the spectral analysis parameters are properly configured.

Verify that bandpass filters are used in the clock and input signal paths,
and that low-noise signal sources are used.

Содержание ADS54J64

























Результаты поиска

Содержание ADS54J64

Отзывы:

Похожие инструкции для ADS54J64

Бренды по названию

Популярные бренды

Texas Instruments ADS54J64, Руководство пользователя

Результаты поиска

Содержание ADS54J64

Отзывы:

Похожие инструкции для ADS54J64

Бренды по названию

Популярные бренды