Texas Instruments ADS54J64 Скачать руководство пользователя страница 6

Страница: 6 / 24

Quick Start Guide

www.ti.com

SBAU290 – September 2017

Submit Documentation Feedback

ADS54J64 Evaluation Module

2.2.1

TSW14J56EVM Setup

Set up the TSW14J56EVM device by following these instructions:

1. Connect the ADS54J64EVM device to the TSW14J56EVM device using the FMC connectors.

2. Connect the included 5-V power supply to connector J11 (5-V IN) of the TSW14J56EVM device.

3. Connect the included mini-USB cable to the USB connector (J9) of the TSW14J56EVM device.

4. Move the power switch (SW6) of the TSW14J56EVM device to the

position.

2.2.2

ADS54J64EVM Setup

Set up the ADS54J64EVM device by following these instructions:

1. Connect the included 5-V power supply to the PWR IN (J14) connector.

2. Verify that JP7 and JP3 and are shorted at positions 2 – 3.

3. Verify that JP2 is shorted.

4. Connect the included mini-USB cable to the USB connector (J13).

5. Set the clock input signal generator for 61.44 MHz and 10 dBm.

6. Connect the

Clock Signal

generator to the LMK_CLK_IN (J12) connector.

7. Place the bandpass filter between the signal generator and the connector, to remove noise from the

signal.

8. Set the analog input signal generator for 90 MHz and 13 dBm.

9. Connect the 6-dB attenuator to the DIN (J1) input.

10. Connect the

Analog Input Signal

generator to the 6-dB attenuator.

11. Place the bandpass filter between the analog signal generator and the attenuator input, to remove

noise and harmonics from the signal generator.

12. Turn on all signal generators.

2.3

Software Setup Procedure

The software can be opened and configured once the hardware is properly set up.

2.3.1

ADS54J64 GUI Configuration

Set up the ADS54J64EVM GUI by following these instructions:

1. Open the ADS54J64EVM GUI from the Start Menu

→

All Programs

→

Texas Instruments

→

ADS54J64 EVM.

2. After the GUI starts, verify that the green USB Status indicator in the top right corner of the GUI is

illuminated.

3. From the INTRO tab, press the

Configure LMK04828

button labeled as "Fclk=983.04MHz". To quickly

evaluate device performance and check EVM functionality, the ADS58J64 EVM GUI has two sampling
rate options to choose from, 983.04 MHz and 737.28 MHz.

4. Press the

ADC_RESET (SW1)

button on the ADS54J64EVM device.

5. Press the

Configure ADS54J64

button labeled as "983.04MHz Nyquist 1".

6. Press the Disable LMK04828 SYSREF to ADC button.

Содержание ADS54J64

























Результаты поиска

Содержание ADS54J64

Отзывы:

Похожие инструкции для ADS54J64

Бренды по названию

Популярные бренды

Texas Instruments ADS54J64, Руководство пользователя

Результаты поиска

Содержание ADS54J64

Отзывы:

Похожие инструкции для ADS54J64

Бренды по названию

Популярные бренды