32
5.4.3 Braking
The machine already slows down considerably by just
releasing the drive pedal.
If need faster breaking, use the brake pedal (
☛
4.5)
5.4.4 Reverse
Reverse must be engaged only when the
machine has stopped moving.
When the machine has stopped moving, start reversing
by pressing the drive pedal in direction
«R»
(
☛
4.9).
5.4.5 Grass cutting
To start cutting:
•
Move the throttle to «FAST»
•
Raise the cutting deck as high as possible
•
Engage the blades (
☛
4.8)
•
Start moving forwards on the grass very slowly and
with utmost caution, as already described
•
Regulate the cutting height and speed considering
the conditions of the lawn
(the height, density and dampness of the grass).
When cutting on sloping ground, reduce your
speed to ensure safe conditions.
Whatever the conditions, always reduce the speed if
you notice a drop in engine speed.
If you travel too fast compared to the amount of grass
being cut, you will not be able to mow/cut the grass
well.
Disengage the blades and raise the cutting deck as
high as possible whenever you need to get past an
obstacle.
5.4.6 Use of mulching function
See Fig. 22
Mulching is ideal for ornamental lawns. With the
mulching cover fitted in the cutting deck, the grass is cut
into very tiny pieces, which disappear between the
blades of grass and rot down to provide natural fertilizer
for the grass.
To use the mulching function, lift up the side discharge
guard and attach the included mulching cover to the
hole of the deck. Make sure the upper part is placed on
the axle under the guard and secure it to the hole of the
deck with the 2 hooks.
Important:
The grass must be dry and not too long to
get the best results. Mulching therefore requires regular
and more frequent mowing – once or twice a week to
work optimally. If the grass becomes too long, it can
make the engine stop due to overload. If this happens,
either raise the cutting height or use the side discharge
function.
5.4.7 End of mowing
When you have finished mowing, disengage the blades,
lower the engine speed and ride the machine with the
cutting deck raised as high as possible.
5.4.8 End of work
Stop the machine, move the throttle to «SLOW» and
turn off the engine by turning the key to «OFF». When
the engine has stopped, close the air valve on fuel lid.
(
☛
5.4.1)
To avoid backfire, position the throttle on
«SLOW» for 20 seconds before stopping the
engine. Always take out the ignition key before
leaving the machine unattended!
To keep the battery charged, do not leave the
key in the «ON» position when the engine is not
running.
5.4.9 Cleaning the machine
After use, clean the outside of the machine. Clean the
plastic parts of the body with a damp sponge using
water and detergent, taking care not to wet the engine,
the electrical parts or the electronic circuit board located
under the dashboard.
Never use hose nozzles or harsh detergents to
clean the bodywork or the engine!
When washing the inside of the cutting deck
and the collector channel, the machine must be
on firm ground with:
•
The grass-catcher or stone-guard fitted
•
The operator seated
•
The engine running
•
The transmission in neutral
•
The blades engaged
Connect a water hose to each of the pipe fittings at a
time and run water through each one for a few minutes,
with the blades moving. See Fig. 23
When washing, the cutting deck should be lowered right
down.
5.4.10 Storage and inactivity for long periods
See Fig. 24
If you intend not to use the machine for a long period
(more than 1 month), disconnect the battery cables and
follow the instructions in the engine instruction manual.
Empty the fuel tank by disconnecting the tube situated
at the inlet of the fuel filter and follow the instructions in
the engine manual.
Carefully
remove any dry grass cuttings which
may have collected around the engine or
silencer to prevent their catching fire the next
time the machine is used!
Put the machine away in a dry, sheltered place and
preferably covered with a cloth
The battery must be kept in a cool and dry
place. Before a long storage period (more than
1 month), always fully charge the battery, and
then recharge before using again.
The next time the machine is used, check that there are
no fuel leaks from the tubes, fuel stopcock or
carburetor.
5.4.11 Card protection device
The electronic circuit board has a self-resetting
protector which breaks the circuit if there is a fault in the
electrical system. It results in the stopping of the engine
and the switching off of the lamp.
The circuit automatically resets after a few seconds, but
the cause of the fault should be ascertained and dealt
with to avoid reactivating the protection device.
Содержание XC140-98
