Texas Equipment TCZ 5800, Руководство пользователя

Страница: 14 / 24

14
Chain and guide bar assembly
See Fig. 2.
1. Remove battery.
2. Disengage the chain brake (pull the front hand
guard backwards)
3. Place the chainsaw on any suitable flat surface
with the oil filler cap facing downwards.
4. Remove the sprocket cover plate by loosening the
nut.
5. Remove the transportation guard (A)
6. Fit the chain onto the drive sprocket at the tip of the
bar. Make sure the teeth are pointing forwards
towards the tip of the guide bar.
7. Fix the chain around the drive sprocket and mount
the guide bar on the chainsaw, so that the
fastening bolt fit into the keyway of the guide bar.
8. Adjust the chain tension screw (A), so the pin (B) is
matching the hole in the bar. Use the chain tension
screw to get the correct tension in the chain.
9. Ensure that the chain sits precisely on the guide
bar.
The chain is correctly tensioned when it is still
possible to raise it by 2-4 mm
10. Fit sprocket cover and tighten the nut.
Mark sure the chain is placed correctly.
Chain tensioning . See Fig. 3.
For future chain tensioning, loosen the nut, adjust the
chain tension screw and tighten the nut again. Use the
included tool.
4. Battery
This product is delivered without battery and charger. It
is sold separately.
To get the best performance of the chainsaw, it is
recommended to use the 4.0 Ah battery.
Warning: Do not try to disassemble, short circuit or put
it to extreme heat or fire, as it can cause serious inquiry
and permanent damage to the battery!
The battery pack is only about 30% charged when
delivered
Charging
•
Only use the original charger with
art. no. 90070054
•
Before the battery is being used the first time, it is
recommended to fully charge it first.
LED lights Battery Pack
All LEDs are lit Fully charged (75-100%).
LED 1, LED 2, LED 3
are lit.
The battery pack is
50%-75% charged
LED 1, LED 2
are lit.
The battery pack is
25%-50% charged.
LED 1 are lit
The battery pack is
0%-25% charged
LED 1 flashes
The battery pack is empty.
Charge the battery.
Note: The indicator lighs is only indicative indications,
and is not accurate power indications.
Important: To protect the battery from total
discharge, the machine will stop, when the battery is
nearly empty.
The machine must not be started up again after
automatic shutdown, as it can damage the battery.
The battery must be recharges before the work can
continue.
For further information, see the user manual which is
included with the battery.
5. Battery waist bag
See Fig. 4
To keep the weight of the chainsaw down, the battery
is kept in a a bag, which is put around your waist. It is
connected to the chainsaw via a cable.
1. Inset the battery in the waist bag. Turn it the right
way, so it easily slides into place.
2. Indset the cable socket (1) in the rear of the
chainsaw.
3. Use the velcro strap (3) near the battery
compartment to keep excess cable in place.
4. To remove the cable from the chainsaw, pull back
the metalpart on the socket, turn the socket 45
degrees anti-clockwise and pull the cable out (3).
6. Charger
A full charge takes around 60 min for 2.0 Ah batteri and
120 min for 4.0 Ah battery.
•
Only use the original charger, which is included
with the product.
•
Do not try to charge other type of batteries in the
charger, other than the original batteries with art.
no. 90070051 (2.0 Ah) or 90070052 (4.0 Ah).
•
Keep the charger in a dry and warm environment
(10-25 degrees C) and only use it indoor. It should
be connected to a normal 230V AC socket.
•
Before the battery is being used the first time, it is
recommended to charge it fully.
•
The surface of the battery can become warm
during charging. This is normal.
•
Do not cover battery or charger during charging.
Allow free ventilation of air.
Insert the battery into the slots of the charger and
slide it into place until it locks.
There are 4 lights on the charger indicating the status
and state of charge of the battery
Status
Charging
Fully charged
Evaluate
Defective