Texas Equipment RAZOR 4200Li, Руководство пользователя

Страница: 15 / 24

15
Operation
Safety key
The motor unit has a safety key, which is placed under
the battery cover. If the safety key is removed, the
power is disconnected, and it cannot start. See
illustration 9
It is always recommended to remove the safety key:
•
When the lawn mower is left unattended (to
prevent uninteded start, e.g. by minors)
•
Before clearning and maintenance
•
Before remove grass blockings
To remove the safety key, turn it to the position ”O” and
pull it out. To insert the safety key, inset it in postion “O”
and turn it to position ”–”. Only then the motor can start.
Cutting height adjustment: Illustration 10
The mower has 6 different heights. The cutting height
ranges from 25 mm to 75 mm
Start
Never start the mower directly on long grass.
1. Open the batttery cover on the motor unit, slide in
the battery and click it in place.
2. Make sure the safety key is activated and in correct
position ”–” ((Illustration 9).
3. The key on the motor unit should be pressed
towards ”L”, if the battery is placed in left socket
and “R” if batteri is placed in right socket
(Illustration 11).
4. Hold the start button (A)down and activate the
handlebar for engine brake (B) to start the motor.
Release startbutton once started.
5. Hold the bar for self-propelled (C) in order to start
mowing (only Razor 4220TR-Li)
Note: As long as operating the mower, the bar
forengine brake must be engaged.
Stop: Illustration 12
1. Release the engine brake and self-propelled bar*
to turn off the mower and the engine
* Only Razor 4220TR-Li
Note: The blades will still rotate at up to 3 seconds
after stopping.
Remove the battery
To remove the battery, press and hold the latch button
under the battery and pull it out (Illustration 13)
There is space for an addtional battery in the motor unit.
This can be purchased seperately.
If 2 batteries are being used, you must manually select
which of the 2 batteries that should be used. It is done
by turning the key toward L or R and choose which
battery that should be used. (Illustration 11)
Working time
The working time per full charge depends of several
factors, like length of grass, cutting height and cutting
methods (mulching, collection. side discharge).
Blade
Inspection of the blade
•
Tilt the mower with the front upwards.
•
Inspect blade for damage, cracks or excessive rust
or corrosion.
•
Check that the blade bolt is tightened.
Note:
A dull blade can be sharpened! But a blade that
is worn, bent, cracked or otherwise damaged must be
replaced.
Removing the blade: See illustration 14
If you remove the blade to sharpen or replace it, you
must use a torque wrench and some heavy gloves to
protect your hands.
1. Loosen the blade bolt with the included tool. Use a
piece of wood to prevent the blade from turning
around.
2. Remove the bolt, washer, blade and blade holder
in that order
3. Sharpen or replace the blade.
4. Insert the blade holder, blade, washer and bolt in
that order.
5. Tighten the blade bolt with 50 Nm with the included
tool. Use a piece of wood to prevent the blade from
turning around.
Warning : A blade must be sharpened so it is in
100 % balance, otherwise it may cause vibrations that
could damage the engine. Damage to engine due to
faulty sharpening is not covered by warranty. We
therefore recommend letting a service center sharpen
the blade.
Storage and maintenance
Maintain your lawnmower: Check all bolts, screws,
nuts and deck. Dismount the blade and the belt plastic
cover for regular cleaning. Always make sure that the
blade is sharp. Keep the motor unit free from grass and
dirt. It’s a good idea to take your lawn mower to an
annual service check with your authorized service
dealer. See your nearest service center at
www.texas.dk.
Storage: After use the lawnmower kept in a dry and
clean room. Clean the machine after every use. Grass
and dirt must be removed from the underside of the
deck. Remove the safety key before cleaning and
storage.
Winter storage: Spray silicone lubrication into the
cables and move them.
Finally, clean the mower thoroughly. Dip a cloth in oil
and luricate metal parts to prevent rust. For storage of
battery, see “Battery” section.