Texas Equipment 90070064, Руководство пользователя

Страница: 12 / 20

12
NOTE : Always remove the battery before assembly and
maintenance.
Mounting of the P-handle. See Fig. 2
1. Loosen the 2 screws on the handlebracket
2. Mount the handle on the shaft and adjust position
3. Tighten the 2 screws again, so the handle is fixed
Mounting of the guard. See Fig. 3
1. Loosen and remove the 2 screws from the guard
2. Mount the guard under the shaft
3. Tighten the the 2 screws again so the guard is
fixed
Place the guard on the motor house and fix it with the 2
included screws. The knife on the side will shorten the
nylon line if it becomes too long.
This guard is intended to prevent loose objects from
being thrown towards the operator. The guard also
protects the operator from accidental contact with the
trimmer head.
Check that the guard is undamaged and not cracked.
Replace the guard if it has been exposed to impact or is
cracked.
Mounting of shaft. See Fig. 4
1. Loosen thw wing knob (A)
2. Remove the end cap from the attachment shaft
3. Pull out the shaft-release knob (B)
4. Push in the attachmentshaft (C) until you hear a
clear “click” sound”.
5. Tighten the wing knob (A)
Mounting of blade. See Fig 5A
1. Fit the Allen key in the hole of the gear to lock the
gear in place.
2. Fit the washer blade, washer and the holder onto
the axle.
3. Fit the nut. Fasten tightly anticlockwise. Make sure
the blade is securely fastened.
Ensure that the blade is tightly fastened
Mounting of trimmer head. See Fig 5B
1. Fit the Allen key in the hole of the gear to lock the
gear in place.
2. Fit the washer.
3. Mount the trimmer head onto the shaft, turn it in
place and make sure it is securely fastened.
Mounting of polesaw
1.
Attach the polesaw to the middle tube and fasten.
2. Mount the guide bar and chain,
Pay attention that the chain is facing the right way.
3. To loosen/tighten the chain, the adjustment screw
in front of the saw is used.
It is recommended to check and add chain oil every
30-45 min. See the “Maintenance” section.
Mounting of pole-hedge trimmer
1.
Remove the protection cap from the hedge trimmer
unit.
2. Attached the tube into the hedge trimmer. See the
small hole on tube to know which direction goes in.
Tighten the screw.
3. Attach the hedge trimmer to the engine unit and
fasten.
The hedge trimmer tube can be placed in a transport
angle. When the hedge trimmer is being used, the tube
must be turned back in work-position and the screw
must always be tighten again before use.
The blades must be kept lubricated to prevent friction
and to extend the durability.
4. Battery
This product is delivered without battery and charger. It
is sold separately.
Warning: Do not try to disassemble, short circuit or put
it to extreme heat or fire, as it can cause serious inquiry
and permanent damage to the battery!
The battery pack is only about 30% charged when
delivered.
Charging
•
Only use the original charger with
art. no. 90070054
•
Before the battery is being used the first time, it is
recommended to fully charge it first.
LED lights Battery Pack
All LEDs are lit Fully charged (75-100%).
LED 1, LED 2, LED 3
are lit.
The battery pack is
50%-75% charged
LED 1, LED 2
are lit.
The battery pack is
25%-50% charged.
LED 1 are lit
The battery pack is
0%-25% charged
LED 1 flashes
The battery pack is empty.
Charge the battery.
Note: The indicator lighs is only indicative indications,
and is not accurate power indications.
Important:
To protect the battery from total
discharge, the machine will stop, when the battery is
nearly empty.
The machine must not be started up again after
automatic shutdown, as it can damage the battery.
The battery must be recharges before the work can
continue.
For further information, see the user manual which is
included with the battery.
5. Charger
A full charge takes around 60 min for 2.0 Ah batteri and
120 min for 4.0 Ah battery.
•
Only use the original charger, which matches this
product.
•
Do not try to charge other type of batteries in the
charger, other than the original batteries with art.
no. 90070051 (2.0 Ah) or 90070052 (4.0 Ah).
•
Keep the charger in a dry and warm environment
(10-25 degrees C) and only use it indoor. It should
be connected to a normal 230V AC socket.
•
Before the battery is being used the first time, it is
recommended to charge it fully.
•
The surface of the battery can become warm
during charging. This is normal.