Texas Equipment 90070048, Руководство пользователя

Страница: 13 / 20

13
For further information, see the user manual which is
included with the charger.
Important:
The charger will stop, when the battery is
full. However, it is not recommended to leave the
battery in charger for more than 24 hours.
It is recommended to drain the battery completely and
fully charge it whenever possible, as it can increase
the health of the battery. But partial charge will not
damage the battery.
To remove the battery from the charger, hold the
button down and pull the battery out.
Before winter storage, the battery should be fully
charged and kept warm at 10-20 degrees C. Charge it
every 3 months. Make sure to keep ventilation holes
clean and free from dirt.
Store the charger indoor between 5-25 degrees C.
6. Operation
Safety key. See Fig. 4
The motor unit has a safety key, which is placed under
the battery cover. If the safety key is removed, the
power is disconnected, and it cannot start.
It is always recommended to remove the safety key:
•
When the lawn mower is left unattended (to
prevent uninteded start, e.g. by minors)
•
Before clearning and maintenance
•
Before remove grass blockings
To remove the safety key, turn it to the free position
and pull it out. To insert the safety key, inset it and turn
it to run position. Only then the motor can start.
Cutting height adjustment. See Fig. 5
The mower has 7 different heights. The cutting height
ranges from 26 mm to 90 mm
Start
Never start the mower directly on long grass.
1. Open the batttery cover on the motor unit, slide in
the battery and click it in place. Close the cover.
See Fig. 6
2. Make sure the safety key is activated and in correct
position.
3. Push the main switch (1) for about 2 seconds untill
the power indicator shows green light.
4. Hold the start button (2) down and activate the
handlebar for motor brake (3) to start the motor.
Release start button once started.
See Fig. 7
5. Hold the handlebar for self-propelled function in
order to start moving, while keeping the handlebar
for motor brake activated (only LMZ 5800TR).
See Fig. 8
Note: As long as operating the mower, the handlebar
for motor brake must be engaged.
Variable speed. See Fig. 9
(only LMZ 5800TR).
The sepf-propelled speed can be adjusted
electronically.via the (+) (
–)
buttons in the display panel.
Choose the desired speed. If the grass is long, the
speed should be reduced to ensure a better cut.
Stop:
Release the engine brake bar (and self-propelled
handle) to turn off the mower and the motor.
Note: The blades will still rotate at up to 3 seconds
after stopping.
Low battery power
Once the power capacitry of battery becomes low, the
power indicator on display panel will turn red.
Remove the battery
To remove the battery, press and hold the release
buttons on each side of the battery and pull it out.
There is space for 2 batteries in the motor unit. One of
the battery chambers is only for storage of battery.
If want to switct battery, the two batteries must be
switched around physically.
Working time
The working time per full charge depends of several
factors, like battery capacity (Ah). length of grass,
cutting height, cutting methods (mulching, collection)
and drive speed.
7. Overload-/Overheat protection
Overload protection
The lawn mower is equipped with a overload protection,
which will stop the motor if it is overloaded.
Avoid going too fast over long grass or set the height
adjustment to a higher position.
If the motor switches off, remove the battery, remove
grass from under the deck, from the rear discharge hole
and empty the grass collector.
Battery overheat protection
The battery generates heat during use. If the
temperature exceeds 70
o
C, to protection circuit will
immediately turn off the mower to protect the battery
from damage. If this happens, let the battery cool down
and restart the lawn mower.
8. Blade
Inspection of the blade
•
Tilt the mower to the side.
•
Inspect blade for damage, cracks or excessive rust
or corrosion.
•
Check that the blade bolt is tightened.
Note:
A dull blade can be sharpened! But a blade that
is worn, bent, cracked or otherwise damaged must be
replaced.
Removing the blade: See Fig. 10
If you remove the blade to sharpen or replace it, you
must use a torque wrench and some heavy gloves to
protect your hands.
1. Loosen the blade bolt with the included tool. Use a
piece of wood to prevent the blade from turning
around.
2. Remove the bolt and blade
3. Sharpen or replace the blade.
4. Insert the blade and bolt
5. Tighten the blade bolt with 50 Nm with the included
tool. Use a piece of wood to prevent the blade from
turning around.