Texas Equipment 90063273, Руководство пользователя

Страница: 12 / 24

12
Mounting
Unpacking
Remove the mower from the box by pulling the machine
out.
Warning: Ensure that the cable is not pinched.
Handlebar: Fig. 3+4
1. Attach the lower handlebar on the lawn mower and
fix it with the quick fix knops in both sides. Do not
overtighten the knops! Fig.3
2. Attach the upper handlebar on the lower handlebar.
Fasten with the quick fix knops in both sides. Fig. 4
3. Customize the cable and secure with cable clamp
Fig. 4.
Mounting the grass collector: Fig. 5
1. Attach the grass collector behind the lawn mower
under the rear deflector guard.
Mulching plug: Fig. 6
1. Insert the mulching plug, if you want to mow with
mulching functionality.
NB Don’t use the grass collector when mulching cutting.
Important: Remember to remove the mulching plug,
when using the grass collector.
Battery
This model is sold both with and without battery/charger
Warning:
Do not try to disassemble, short circuit or put
it to extreme heat or fire, as it can cause serious inquiry
and permanent damage to the battery!
Battery pack is not fully charged when delivered.
Charging
•
Only use the original charger with
art. no. 90063242 or 90063241
•
Before the battery is being used the first time, it is
recommended to fully charge it first.
LED lights Battery Pack
All LEDs are lit Fully charged (75-
100%).
LED 1, LED 2, LED 3
are lit. The battery pack is
50%-75% charged
LED 1, LED 2
are lit. The battery pack is
25%-50% charged.
LED 1 are lit
The battery pack is
0%-25% charged
LED 1 flashes
The battery pack is
empty. Charge the
battery.
Note: The indicator lighs is only indicative indications
and is not accurate power indications.
Important:
To protect the battery from total discharge,
the machine will stop, when the battery is nearly empty.
The machine must not be started up again after
automatic shutdown, as it can damage the battery.
The battery must be recharges before the work can
continue.
Charging
A full charge takes around 60 min for 2.0 Ah batteri
and 120 min for 4.0 Ah battery.
•
Only use the original charger*
•
Do not try to charge other type of batteries in the
charger, other than the original batteries with art.
no. 90063245 (2.0 Ah) or 90063246 (4.0 Ah).
•
Keep the charger in a dry and warm environment
(10-25 degrees C) and only use it indoor. It
should be connected to a normal 230V AC
socket.
•
Before the battery is being used the first time, it is
recommended to charge it fully.
•
The surface of the battery can become warm
during charging. This is normal.
•
Do not cover battery or charger during charging.
Allow free ventilation of air.
Insert the battery into the slots of the charger and
slide it into place until it locks. Fig. 7.
There are 4 lights on the charger indicating the status
and state of charge of the battery
Status
Charging
Fully charged
Evaluate
Defective
Important:
The charger will stop, when the battery is
full. However, it is not recommended to leave the
battery in charger for more than 24 hours.
It is recommended to drain the battery completely and
fully charge it whenever possible, as it can increase
the health of the battery. But partial charge will not
damage the battery.
To remove the battery from the charger, hold the
button down and pull the battery out.
Before winter storage, the battery should be fully
charged and kept warm at 10-20 degrees C. Charge it
every 3 months. Make sure to keep ventilation holes
clean and free from dirt.
Store the charger indoor between 5-25 degrees C.