4 Zone DMX and RF wall panel
for Single Colour, Tunable White, RGB, RGBW
and RGBCCT LED strip
www.teucerled.co.uk
V002-11-2019
Synchronising the wall panel to the receiver
1)
Ensure the receiver has power. Press the match button on the receiver. LED Indicator will start flashing
slowly.
2)
Choose the zone you wish to allocate on the panel within 5 seconds after pressing the match button.
The LED indicator on the receiver will flash rapidly 5 times and then stop flashing. The controller is now
synchronised with the receiver.
Match button
LED Indicator
R3C
Press the zone
you wish to allocate
SCENE
S
ZONE
ZONE
ZONE
ZONE
1
2
3
4
SPEED
BRIGHT
MODE
M
CCT
RGB
3)
Repeat the process to allocate zones for all
receivers.
Note! RF technology allows for greater flexibility when it comes to controlling simple or complex lighting installations
without the need of additional cabling. There are some limitations where installations have the receivers enclosed in
electrical boxes or hidden away in a ceiling , reducing the RF signal strength and therefore the communication range.
In order to overcome these RF Signal restrictions we suggest the following when synchronising our RF controllers and
receivers:
•
Keep the distance within 10 meters from the controller to the receiver. The remote can operate up to 30 meters if
signal is uninterrupted by obstacles.
•
When expanding your lighting, always try and use a signal repeater (PR-RGB(N)), where possible.
Match button
LED indicator
Pu
sh
-D
im
G
ND
R4C
Match button
LED indicator
R5C
+
-
+
IN
P
U
T
12
-
24
V
D
C
Uin=12
-
24VDC
Iin
=
15.5A
RGB+CCT 5CH LED Controller
Uout=5
×
(12
-
24)VDC
Iout=5
×
3A
Pout=5
×
(36
-
72)W
Temp Range: -20
℃
~
+
55
℃
Made
in
China
O
U
T
P
U
T
W
4
+ +
2.4G wireless control
RoHS
W
5
0.5-1.5mm
2
6
-
8mm
Synchronising the wall panel to the DMX decoder
Address Setting in Various modes when using a single decoder:
LED strip type
mode
Channel
Zone 1 DMX
address
Zone 1 DMX
address
Zone 1 DMX
address
Zone 1 DMX
address
Single Colour
W
W
W
W
W
1-5
6-10
11-15
16-20
Tunable White
WW CW WW CW
-
1-5
6-10
11-15
16-20
RGB
R
G
B
-
-
1-5
6-10
11-15
16-20
RGBW
R
G
B
W
W
1-5
6-10
11-15
16-20
RGBCCT
R
G
B WW CW
1-5
6-10
11-15
16-20
Note! We recommend using the controller when controlling all lighting as a single zone.
Please note that with the DIM-DMX1CH(N) and DIM-DMX5CH one can use the manual button to switch ON the con-
nected LED strips and check the operation by cycling through the various modes.
•
When expanding your lighting always try and use a signal repeater (PR-RGB) where possible.
•
If using DMX over 55mtrs it is recommended to use a DMX amplifier for longer distances.
•
If the recoil effect occurs because of the long DMX signal line or bad DMX line quality, please try to connect a 0.25W
90-120Ω terminal resistor at the end of the DMX signal line.
4)
To restore the receiver to the factory default settings
and delete the allocated controller, press and hold the
match button on the receiver longer than 5 seconds
until the LED indicator flashes quickly 5 times.
