EN
8
Operation and Storage Manual of Panel Heater
Quick menu
Push the “Mode” button
to start quick already configured program. Select
by pushing any of the buttons:
or
and confirm with “Mode” button
. The program going to start to work.
Content function:
- Comfort
- Eco
- Sleep
- Delay start
- Weekly schedule
Exit from the any mode – with single pushing of ON/OFF button
.
Errors mode:
If the display shows “t1” or “t2“, this means that the self-diagnostic system has
found a problem with the temperature sensor. “t1” indicates a disconnected
cable at the sensor, while “t2” indicates short circuit at the sensor. In this case
the electric convector will be automatically switched off and it can be switched
on again only after the problem has been fixed. The problem has to be handled
by a qualified specialist.
DISCONNECTION FROM THE POWER SUPPLY:
If the electric convector is disconnected from the mains, this will not affect
the set temperature and the mode of operation which has been active prior
to its disconnection. If for example the convector has been in “Heating” mode,
after it has been disconnected and reconnected to the mains, it will continue
operating in the same mode with the same set temperature.
The principle of operation of the electric convector with energy-independent
memory is to store the settings for 120 minutes guaranteed, and up to 180
minutes not guaranteed.
If the time is more than 120 min the appliance going to Stand by mode.
PROTECTION
• The appliance is equipped with a safety thermo turn-off device, which
automatically turns the heater off in cases of extreme temperature of the
panel heater /i.e. overheating of the appliance/.
• The safety thermo turn-off device will automatically restore the heater
operation when the temperature of the appliance falls below the
permissible ultimate values.
CLEANING
• It is compulsory first to turn off the appliance through its power
switch and to disconnect it from the power socket. Before starting the
cleaning session you should wait until the panel heater cools down in a
disconnected state.
• The panel heater can be cleaned with little efforts at the appliance
rear part – just press the “P”-shaped braces /figure 2/ at the back of the
appliance so that you can dismantle it and consequently you can clean the
rear part of the appliance.
• Clean the heater body with damp cloth, vacuum cleaner or a brush.
• Never immerse the appliance into water – there is danger for your life from
electric shock!
• Never use gasoline, thinner or hard abrasive products to clean the
appliance, because they will damage the appliance coating.
STORAGE
• Before putting the panel heater away let it cool down after you have
disconnected it from the power socket
• Use the appliance original packing to store it, if the panel heater will not
be in use for a long period of time. By storing the product in its original
packing you protect it from excessive dirt and dust accumulation.
• Never put a hot panel heater in its packing!
• It is necessary the product to be stored at a dry and dark place, protected
from direct sun light.
•
It is explicitly forbidden to store the panel heater in damp and wet premises.
MAINTENANCE OPERATIONS OF THE APPLIANCE
• In case of appliance malfunction, please contact the authorized service
center closest to your location. /service centers are indicated in appliance
warranty documents/.
•
Important:
In case of a claim and/or violation of your consumer rights,
please contact the supplier of this appliance at the indicated locations or
via the Internet page of the company: www.tesy.com
DIMENSIONS OF HEATED VOLUME AND HEATED AREA OF A ROOM /
APPLIANCE MODELS
Model
Heated volume
Heated area
CN 051 050 EI [CLOUD] [AS] W
- 500W
10* - 15 m
3
4* - 6 m
2
CN 051 100 EI [CLOUD] [AS] W
- 1000W
20* - 30 m
3
8* - 12 m
2
CN 051 150 EI [CLOUD] [AS] W
- 1500W
30* - 45 m
3
12* - 18 m
2
CN 051 200 EI [CLOUD] [AS] W
- 2000W
40* - 60 m
3
16* - 24 m
2
CN 051 250 EI [CLOUD] [AS] W
- 2500W
50* - 70 m
3
20* - 28 m
2
CN 051 300 EI [CLOUD] [AS] W
- 3000W
60* - 80 m
3
24* - 32 m
2
* Minimum guaranteed heated volume (area) for heating at an average capacity of heat transmission
factor λ=0.5 W/(m
2
K) for a heated room. Higher values of heated volume (area) can be achieved at an
average value of λ=0.35 W/ (m
2
K). Standard height of heated rooms – 2.5 meters.
Environment protection instructions
Obsolete electric appliances contain valuable materials and consequently they
should not be treated as domestic waste! We ask for your cooperation and your
active contribution to protect the resources and the environment. Please submit
your out-of-use appliances to the organized buy-back stations (if there are such).
Содержание CN051 100 EI CLOUD W
Страница 63: ......