manualshive.com logo in svg

Tesla HPWC, Руководство по установке

Поделиться
Скачать
Tesla HPWC Скачать руководство пользователя страница 18

14

HIGH POWER WALL CONNECTOR INSTALLATION GUIDE

Step Six - Confirm a Successful Installation

1

Set the DIP switches, located in the lower 
right-hand portion of the connector, to the 
test setting shown here. Use a pointed 
non-conductive object such as a pen.

2

While holding the front cover near the 
connector, re-connect the ribbon cable.

3

Hang the front cover over the hinge 
located at the top of the connector. Do not 
secure the front cover yet.

4

Turn on the power.

5

Hold the RESET button for five seconds. 
This button is located on the lower right 
side of the High Power Wall Connector.

You should hear the contacts close and see 
the High Power Wall Connector’s lights 
sequentially illuminate green. 

If the RED error light illuminates or flashes, see 
the Troubleshooting table on page 18 and 
resolve the error before continuing.

If the RED error light is not illuminated or 
flashing, continue with the next two steps.

DIP
switches

Test Mode 

RESET 
button is 
located on 
the lower 
right side

HPWC_Install_Guide.book  Page 14  Wednesday, April 2, 2014  3:30 PM

Содержание HPWC





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды